{
 "version": "2026-10-20",
 "license": "Dimension sheets: CC BY 4.0. Standard and published-size files: CC BY 4.0. Xem Studio's own designs (files_license = Xem Studio Design License): free to use and sell things from, not to redistribute as files — https://xemstudio.com/license/. Other publishers' files: their own license, linked beside them.",
 "slug": "crank-set-12mm-shafts",
 "name": "Crank set for Ø12 shafts: webs, link web, con-rods and clevis",
 "kind": "hardware",
 "category": "Hardware",
 "group": "Gears, cranks & flywheels",
 "year": null,
 "question": "What crank set fits 12 mm shafts?",
 "tags": [
  "htd",
  "crank",
  "crankshaft",
  "con-rod",
  "stirling"
 ],
 "aliases": [
  "stirling built up crank",
  "gamma stirling crank 90 degrees",
  "tri clamp cross crankcase crank"
 ],
 "overall_mm": {
  "length": null,
  "width": null,
  "height": null
 },
 "official_cad": false,
 "xem_status": "free-files",
 "les": true,
 "free_files": 8,
 "url": "https://xemstudio.com/objects/crank-set-12mm-shafts/",
 "sheet_txt": "https://xemstudio.com/objects/crank-set-12mm-shafts/sheet.txt",
 "sheet": {
  "basis": "Exact geometry; designed running gaps between every moving plane",
  "overall_mm": {
   "length": null,
   "width": null,
   "height": null
  },
  "notes": [
   "Built-up crank on Ø12 shafts in 6001 bearings: web A (displacer throw r 4) – Ø5 pin through the displacer con-rod's 625 – link web – Ø5 pin through the piston con-rod's 625 – web C (piston throw r 20). The displacer pin leads the piston pin by 90°.",
   "Planes along the shaft (x): web A disc −9.5..−3.5, displacer con-rod −2.5..2.5, link web 3.5..9.5, piston con-rod 10.5..15.5, web C 16.5..22.5: 1.0 between every rod and web (designed). Pins are Ø5 × 16 dowels pressed in the webs.",
   "Con-rods 60 (displacer, to the clevis on the rod) and 237 (piston, down through the reducer to the piston's cheeks); every eye runs on a 625. Sweep radius 31 (piston eye) inside the 3 in cross bore Ø72.9."
  ],
  "table": {
   "columns": [
    "part",
    "role",
    "size"
   ],
   "rows": [
    [
     "crank-web-r8-b12",
     "displacer web",
     "r 4"
    ],
    [
     "crank-web-link-r8-r20",
     "link web",
     "r 4 / 20"
    ],
    [
     "crank-web-r20-b12",
     "piston web",
     "r 20"
    ],
    [
     "conrod-60-625",
     "con-rod",
     60
    ],
    [
     "conrod-237-625",
     "con-rod",
     237
    ],
    [
     "rod-clevis-6-pin5",
     "rod clevis",
     "Ø6 rod, Ø5 pin"
    ],
    [
     "shaft-12x76",
     "shaft",
     76
    ],
    [
     "shaft-12x210",
     "shaft",
     210
    ]
   ]
  }
 },
 "sheet_text": "Crank set for Ø12 shafts: webs, link web, con-rods and clevis — dimension sheet\nSource: Xem Studio, https://xemstudio.com/objects/crank-set-12mm-shafts/  (sheet CC BY 4.0; files Xem Studio Design License, https://xemstudio.com/license/)\nBasis: Exact geometry; designed running gaps between every moving plane\nCatalog version: 2026-10-20\n\nSizes: see table below\n- Built-up crank on Ø12 shafts in 6001 bearings: web A (displacer throw r 4) – Ø5 pin through the displacer con-rod's 625 – link web – Ø5 pin through the piston con-rod's 625 – web C (piston throw r 20). The displacer pin leads the piston pin by 90°.\n- Planes along the shaft (x): web A disc −9.5..−3.5, displacer con-rod −2.5..2.5, link web 3.5..9.5, piston con-rod 10.5..15.5, web C 16.5..22.5: 1.0 between every rod and web (designed). Pins are Ø5 × 16 dowels pressed in the webs.\n- Con-rods 60 (displacer, to the clevis on the rod) and 237 (piston, down through the reducer to the piston's cheeks); every eye runs on a 625. Sweep radius 31 (piston eye) inside the 3 in cross bore Ø72.9.\n\npart  role  size\ncrank-web-r8-b12  displacer web  r 4\ncrank-web-link-r8-r20  link web  r 4 / 20\ncrank-web-r20-b12  piston web  r 20\nconrod-60-625  con-rod  60.0\nconrod-237-625  con-rod  237.0\nrod-clevis-6-pin5  rod clevis  Ø6 rod, Ø5 pin\nshaft-12x76  shaft  76\nshaft-12x210  shaft  210\n\nFiles elsewhere (not hosted by Xem Studio; license as stated by the publisher):\n- Long Earth Society: Engine builds — web, video — LES site — https://longearthsociety.com/engineering/\n\nFree files (Xem Studio Design License, Xem Studio; STEP + STL, 8 parts): https://xemstudio.com/files/hardware/crank-set-12mm-shafts/index.json\nAPI: https://xemstudio.com/api/geometry?object=crank-set-12mm-shafts\n",
 "sources": [
  {
   "publisher": "Long Earth Society",
   "title": "Engine builds",
   "url": "https://longearthsociety.com/engineering/",
   "formats": [
    "web",
    "video"
   ],
   "license": "LES site",
   "license_verified": true,
   "hosted": false
  }
 ],
 "xem": {
  "status": "free-files",
  "sheet_free": true,
  "mesh_price_usd": null,
  "step_price_usd": null,
  "tolerance_mm": null
 },
 "related": [
  "tri-clamp-bearing-seal-caps-3in",
  "pistons-48x72",
  "dowel-pins-metric",
  "ball-bearings-metric"
 ],
 "fits": [],
 "dimensions": "exact (nominal, no tolerance added)",
 "dimension_rule": "All geometry on Xem Studio is exact (nominal, true size) with no tolerance added. Where a part meets another part, the object lists its mating features (feature, exact size, what it mates with, fit class: press, slide, run, socket, clamp or designed). Apply your process's allowance to those features only; 'designed' gaps are part of the design and stay as drawn. Typical accuracy by process and ISO 286 fits: https://xemstudio.com/tolerances/",
 "mating": [
  {
   "feature": "web and hub bores",
   "exact": "Ø12",
   "mates": "Ø12 shafts (M4 grub on each hub)",
   "fit": "slide",
   "files": "crank-web-"
  },
  {
   "feature": "pin bores",
   "exact": "Ø5",
   "mates": "dowel-5x16 crank pins",
   "fit": "press",
   "files": "crank-web-"
  },
  {
   "feature": "con-rod pockets",
   "exact": "Ø16 × 5",
   "mates": "bearing-625 outer ring",
   "fit": "press",
   "files": "conrod-"
  },
  {
   "feature": "clevis socket",
   "exact": "Ø6 × 14",
   "mates": "displacer rod, M4 grub",
   "fit": "slide",
   "files": "rod-clevis-"
  },
  {
   "feature": "clevis slot and pin",
   "exact": "6.0 wide, Ø5",
   "mates": "5 thick con-rod; dowel-5x16",
   "fit": "press",
   "files": "rod-clevis-"
  },
  {
   "feature": "plane gaps",
   "exact": "1.0 between every web and con-rod plane",
   "mates": "neighbouring webs and rods",
   "fit": "designed",
   "files": "all"
  },
  {
   "feature": "shafts",
   "exact": "Ø12",
   "mates": "bearing-6001 inner rings",
   "fit": "press",
   "files": "shaft-"
  }
 ],
 "fit_classes": {
  "press": "stays put: pin, tube, bearing or magnet held by interference. ISO 286 equivalent: H7/p6 (locational interference) or tighter.",
  "slide": "assembles by hand and is held by a grub, pinch or clamp: shaft in a hub, rod in a socket, spigot in a bore. ISO 286 equivalent: H7/g6 or H7/h6.",
  "run": "turns or slides in use: pin in a link, rod through a guide. ISO 286 equivalent: H8/f7 (close running).",
  "socket": "large sliding fit: syringe barrel, sleeve, bobbin in a bore. ISO 286 equivalent: H9/d9 (free running) or looser.",
  "clamp": "split part that closes on the mating part with screws: make it at size.",
  "designed": "a gap that is part of the design (piston fit option, displacer gap, air gap): do not change."
 },
 "faq": [
  {
   "q": "Why a built-up crank?",
   "a": "One-piece con-rod eyes on 625 bearings slide onto the pins before the webs close up; nothing has to be split."
  }
 ],
 "files_license": {
  "name": "Xem Studio Design License",
  "holder": "Xem Studio",
  "url": "https://xemstudio.com/license/",
  "note": "Xem Studio's own design: free to use, print, modify and sell things made from it; not to be republished or redistributed as files."
 },
 "offers": [
  {
   "file": "crank-web-r8-b12",
   "formats": [
    "step",
    "stl"
   ],
   "price_usd": 0,
   "license": "Xem Studio Design License",
   "step": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/crank-web-r8-b12.step",
   "stl": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/crank-web-r8-b12.stl",
   "note": "crank web, hub type: disc R12 × 6 with a Ø5 pin at r 4 (8 displacer stroke), hub Ø24 × 8, Ø12 bore in the hub only, M4 tapped radial hole"
  },
  {
   "file": "crank-web-link-r8-r20",
   "formats": [
    "step",
    "stl"
   ],
   "price_usd": 0,
   "license": "Xem Studio Design License",
   "step": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/crank-web-link-r8-r20.step",
   "stl": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/crank-web-link-r8-r20.stl",
   "note": "link web 6 thick: Ø5 displacer pin at r 4 and Ø5 piston pin at r 20, 90° apart"
  },
  {
   "file": "crank-web-r20-b12",
   "formats": [
    "step",
    "stl"
   ],
   "price_usd": 0,
   "license": "Xem Studio Design License",
   "step": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/crank-web-r20-b12.step",
   "stl": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/crank-web-r20-b12.stl",
   "note": "crank web, hub type: disc R28 × 6 with a Ø5 pin at r 20 (40 piston stroke), hub Ø24 × 8, Ø12 bore through, M4 tapped radial hole"
  },
  {
   "file": "conrod-60-625",
   "formats": [
    "step",
    "stl"
   ],
   "price_usd": 0,
   "license": "Xem Studio Design License",
   "step": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/conrod-60-625.step",
   "stl": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/conrod-60-625.stl",
   "note": "con-rod 60 centres, 5 thick, Ø16 pockets for 625 bearings, eyes Ø22"
  },
  {
   "file": "conrod-237-625",
   "formats": [
    "step",
    "stl"
   ],
   "price_usd": 0,
   "license": "Xem Studio Design License",
   "step": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/conrod-237-625.step",
   "stl": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/conrod-237-625.stl",
   "note": "con-rod 237 centres, 5 thick, Ø16 pockets for 625 bearings, eyes Ø22"
  },
  {
   "file": "rod-clevis-6-pin5",
   "formats": [
    "step",
    "stl"
   ],
   "price_usd": 0,
   "license": "Xem Studio Design License",
   "step": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/rod-clevis-6-pin5.step",
   "stl": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/rod-clevis-6-pin5.stl",
   "note": "rod clevis: 13 × 14 × 41 block, slot 6 wide for a 5 con-rod, Ø5 pin bore, Ø6 rod socket 14 deep, M4 tapped radial hole"
  },
  {
   "file": "shaft-12x76",
   "formats": [
    "step",
    "stl"
   ],
   "price_usd": 0,
   "license": "Xem Studio Design License",
   "step": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/shaft-12x76.step",
   "stl": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/shaft-12x76.stl",
   "note": "Ø12 × 76 crankshaft, −X (main): blind-cap 6001 to web A's hub"
  },
  {
   "file": "shaft-12x210",
   "formats": [
    "step",
    "stl"
   ],
   "price_usd": 0,
   "license": "Xem Studio Design License",
   "step": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/shaft-12x210.step",
   "stl": "https://xemstudio.com/files/hardware/crank-set-12mm-shafts/shaft-12x210.stl",
   "note": "Ø12 × 210 crankshaft, +X: web C, two 6001, the seal, gear and flywheel"
  }
 ],
 "markdown": "https://xemstudio.com/objects/crank-set-12mm-shafts/index.md"
}