{
 "version": "2026-10-20",
 "license": "Dimension sheets: CC BY 4.0. Standard and published-size files: CC BY 4.0. Xem Studio's own designs (files_license = Xem Studio Design License): free to use and sell things from, not to redistribute as files — https://xemstudio.com/license/. Other publishers' files: their own license, linked beside them.",
 "slug": "snap-tri-clamp-bolt-free",
 "name": "Snap tri-clamp, bolt-free (printable, ½ to 10 in)",
 "kind": "hardware",
 "category": "3D printable tri-clamp",
 "group": "Clamps & fittings",
 "year": null,
 "question": "Is there a tri-clamp clamp that snaps shut without a bolt?",
 "tags": [
  "tri-clamp",
  "clamp",
  "snap",
  "printable",
  "bolt-free"
 ],
 "aliases": [
  "bolt free tri clamp",
  "snap tri clamp",
  "3d printed tri clamp clamp",
  "tool-less tri clamp",
  "6 inch snap tri clamp",
  "8 inch tri clamp printable",
  "10 inch tri clamp printable"
 ],
 "overall_mm": {
  "length": null,
  "width": null,
  "height": null
 },
 "official_cad": false,
 "xem_status": "not-scanned",
 "les": false,
 "free_files": 0,
 "url": "https://xemstudio.com/objects/snap-tri-clamp-bolt-free/",
 "sheet_txt": "https://xemstudio.com/objects/snap-tri-clamp-bolt-free/sheet.txt",
 "sheet": {
  "basis": "Xem Studio design (v7, 6–10 in v8), tested on a 2 in printed joint",
  "overall_mm": {
   "length": null,
   "width": null,
   "height": null
  },
  "notes": [
   "A tri-clamp clamp with no bolt: each piece carries a flush arm whose hooked claw drops into a notch on the next piece only when the two meet — clipped or not, nothing in between. Open with a butter knife in the V at the arm tip.",
   "½ to 8 in: two identical halves. 10 in: three identical 120° segments, because a 10 in half is wider than a 256 mm bed; each segment has one arm and one notch, the same latch.",
   "Prints flat with no supports: every downward face is 45° or steeper, both outer edges carry the same R7 round. Every file fits a 256 × 256 mm bed as exported; the footprint column is one piece as it lies on the bed.",
   "Sized for the printable 45° tri-clamp ferrules and a standard silicone gasket (closes on a 2.0 mm compressed stack). One clamp per flange: ½ and ¾ in share the 25 mm flange, 1 and 1½ in the 50.5 mm flange.",
   "6, 8 and 10 in carry more gasket force, so the wall, the band width and the arm thickness grow with the square root of the flange diameter (from the 4 in values); the claw, the groove and the knife V are the same as on the tested 2 in clamp, so one clamp key opens every size.",
   "The STEP/STL pack (all sizes, ½ to 10 in) is $3 by card, or $2.40 for AI agents paying with x402 at /api/buy/snap-tri-clamp-pack. The dimension sheet is free."
  ],
  "table": {
   "columns": [
    "size",
    "pieces",
    "clamp OD",
    "width",
    "wall",
    "print footprint (one piece)"
   ],
   "rows": [
    [
     "½–¾ in (25 mm flange)",
     "2 halves",
     "43.0 mm",
     "16.0 mm",
     "8.0 mm",
     "42.3 × 26.4 mm"
    ],
    [
     "1–1½ in (50.5 mm flange)",
     "2 halves",
     "68.5 mm",
     "22.5 mm",
     "8.0 mm",
     "67.4 × 42.2 mm"
    ],
    [
     "2 in (64 mm flange)",
     "2 halves",
     "82.0 mm",
     "23.3 mm",
     "8.0 mm",
     "80.7 × 50.6 mm"
    ],
    [
     "2½ in (77.5 mm flange)",
     "2 halves",
     "95.5 mm",
     "24.1 mm",
     "8.0 mm",
     "94.0 × 59.0 mm"
    ],
    [
     "3 in (91 mm flange)",
     "2 halves",
     "109.0 mm",
     "24.9 mm",
     "8.0 mm",
     "107.3 × 67.4 mm"
    ],
    [
     "4 in (119 mm flange)",
     "2 halves",
     "137.0 mm",
     "27.5 mm",
     "8.0 mm",
     "134.9 × 84.8 mm"
    ],
    [
     "6 in (166.9 mm flange)",
     "2 halves",
     "187.8 mm",
     "32.6 mm",
     "9.5 mm",
     "185.7 × 113.3 mm"
    ],
    [
     "8 in (217.7 mm flange)",
     "2 halves",
     "241.3 mm",
     "37.2 mm",
     "10.8 mm",
     "239.1 × 142.9 mm"
    ],
    [
     "10 in (268.5 mm flange)",
     "3 segments (120°)",
     "294.5 mm",
     "41.3 mm",
     "12.0 mm",
     "218.5 × 172.1 mm"
    ]
   ]
  }
 },
 "sheet_text": "Snap tri-clamp, bolt-free (printable, ½ to 10 in) — dimension sheet\nSource: Xem Studio, https://xemstudio.com/objects/snap-tri-clamp-bolt-free/  (sheet CC BY 4.0)\nBasis: Xem Studio design (v7, 6–10 in v8), tested on a 2 in printed joint\nCatalog version: 2026-10-20\n\nSizes: see table below\n- A tri-clamp clamp with no bolt: each piece carries a flush arm whose hooked claw drops into a notch on the next piece only when the two meet — clipped or not, nothing in between. Open with a butter knife in the V at the arm tip.\n- ½ to 8 in: two identical halves. 10 in: three identical 120° segments, because a 10 in half is wider than a 256 mm bed; each segment has one arm and one notch, the same latch.\n- Prints flat with no supports: every downward face is 45° or steeper, both outer edges carry the same R7 round. Every file fits a 256 × 256 mm bed as exported; the footprint column is one piece as it lies on the bed.\n- Sized for the printable 45° tri-clamp ferrules and a standard silicone gasket (closes on a 2.0 mm compressed stack). One clamp per flange: ½ and ¾ in share the 25 mm flange, 1 and 1½ in the 50.5 mm flange.\n- 6, 8 and 10 in carry more gasket force, so the wall, the band width and the arm thickness grow with the square root of the flange diameter (from the 4 in values); the claw, the groove and the knife V are the same as on the tested 2 in clamp, so one clamp key opens every size.\n- The STEP/STL pack (all sizes, ½ to 10 in) is $3 by card, or $2.40 for AI agents paying with x402 at /api/buy/snap-tri-clamp-pack. The dimension sheet is free.\n\nsize  pieces  clamp OD  width  wall  print footprint (one piece)\n½–¾ in (25 mm flange)  2 halves  43.0 mm  16.0 mm  8.0 mm  42.3 × 26.4 mm\n1–1½ in (50.5 mm flange)  2 halves  68.5 mm  22.5 mm  8.0 mm  67.4 × 42.2 mm\n2 in (64 mm flange)  2 halves  82.0 mm  23.3 mm  8.0 mm  80.7 × 50.6 mm\n2½ in (77.5 mm flange)  2 halves  95.5 mm  24.1 mm  8.0 mm  94.0 × 59.0 mm\n3 in (91 mm flange)  2 halves  109.0 mm  24.9 mm  8.0 mm  107.3 × 67.4 mm\n4 in (119 mm flange)  2 halves  137.0 mm  27.5 mm  8.0 mm  134.9 × 84.8 mm\n6 in (166.9 mm flange)  2 halves  187.8 mm  32.6 mm  9.5 mm  185.7 × 113.3 mm\n8 in (217.7 mm flange)  2 halves  241.3 mm  37.2 mm  10.8 mm  239.1 × 142.9 mm\n10 in (268.5 mm flange)  3 segments (120°)  294.5 mm  41.3 mm  12.0 mm  218.5 × 172.1 mm\n\nFiles elsewhere (not hosted by Xem Studio; license as stated by the publisher):\n- Xem Studio: Snap tri-clamp design — web — Publisher's page; dimensions are facts — https://xemstudio.com/\n\nNo true-size file yet: the published figures do not fix the whole shape; a measured scan is planned.\nAPI: https://xemstudio.com/api/geometry?object=snap-tri-clamp-bolt-free\n",
 "sources": [
  {
   "publisher": "Xem Studio",
   "title": "Snap tri-clamp design",
   "url": "https://xemstudio.com/",
   "formats": [
    "web"
   ],
   "license": "Publisher's page; dimensions are facts",
   "license_verified": true,
   "hosted": false
  }
 ],
 "xem": {
  "status": "not-scanned",
  "sheet_free": true,
  "mesh_price_usd": null,
  "step_price_usd": null,
  "tolerance_mm": null
 },
 "related": [
  "printable-tri-clamp-clamps",
  "tri-clamp-45-degree-printable",
  "tri-clamp-gasket"
 ],
 "fits": [],
 "dimensions": "exact (nominal, no tolerance added)",
 "dimension_rule": "All geometry on Xem Studio is exact (nominal, true size) with no tolerance added. Where a part meets another part, the object lists its mating features (feature, exact size, what it mates with, fit class: press, slide, run, socket, clamp or designed). Apply your process's allowance to those features only; 'designed' gaps are part of the design and stay as drawn. Typical accuracy by process and ISO 286 fits: https://xemstudio.com/tolerances/",
 "mating": [],
 "faq": [
  {
   "q": "How do you open it?",
   "a": "Slide a butter knife into the V at an arm tip and lever the tip outward. The V is the same on every size."
  },
  {
   "q": "Does it need supports?",
   "a": "No — it prints flat; every downward face is 45° or steeper."
  },
  {
   "q": "Will the big sizes fit my printer?",
   "a": "Yes on a 256 × 256 mm bed: a 6 in half is 186 × 113 mm, an 8 in half 239 × 143 mm, a 10 in segment 219 × 172 mm, each as exported."
  },
  {
   "q": "Why is the 10 in clamp three pieces?",
   "a": "A 10 in half would be 292 mm wide and does not fit a 256 mm bed even turned diagonally; three 120° segments do, each with the same claw latch."
  },
  {
   "q": "Does the 10 in clamp have printable rims to go with it?",
   "a": "It fits any 10 in rim with the 45° back cone; the 10 in rim itself (268.5 mm flange) needs a printer larger than 256 mm."
  }
 ],
 "files_license": null,
 "offers": [
  {
   "file": "snap-tri-clamp-pack",
   "format": "zip: STEP + STL per size",
   "status": "available",
   "price_usd": 3,
   "url": "https://xemstudio.com/api/buy/snap-tri-clamp-pack",
   "files": [
    "snap-tri-clamp-0.75in-half",
    "snap-tri-clamp-1.5in-half",
    "snap-tri-clamp-2in-half",
    "snap-tri-clamp-2.5in-half",
    "snap-tri-clamp-3in-half",
    "snap-tri-clamp-4in-half",
    "snap-tri-clamp-6in-half",
    "snap-tri-clamp-8in-half",
    "snap-tri-clamp-10in-segment"
   ],
   "payment": "x402 (USDC); returns 402 with PAYMENT-REQUIRED, retry with PAYMENT-SIGNATURE"
  }
 ],
 "markdown": "https://xemstudio.com/objects/snap-tri-clamp-bolt-free/index.md"
}