Library › Hardware › Springs & flexures ·

Mass discs, 0.5 mm flexure leaf and rim shim for 2 in tri-clamp flexures

What add-on masses and shims tune a 2 inch tri-clamp flexure? · Hardware · basis: Natural frequency f = √(k/m) / 2π of the mover on its leaves and bounce gas spring (k_b = γ p A² / V_b, adiabatic); masses from the CAD at 7.9 g/cm³ (assumed); leaf stiffness from the generator's frame model (E 200 GPa assumed)

Also called: linear alternator tuning mass, free piston resonance tuning, soft flexure leaf, change natural frequency free piston

Long Earth Society build part. Tuning parts for my clamp-in linear alternator module. Long Earth Society

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
5 in table

Notes

  • What moves the frequency, largest first: the charge behind the piston, the bounce volume, the leaves, the mass. The discs are the fine trim: four of them lower the frequency by about 5 %, because the mover already carries 865 g of magnets and return path.
  • Coarse tuning without new parts: a stock 2 in spool between face B and the cap (one more gasket and clamp) softens the bounce gas spring. With a 3 in spool: 293 cm³, 17.5 / 28.4 Hz (air 1 bar / helium 10 bar, standard leaves); with a 6 in spool: 428 cm³, 17.1 / 25.2 Hz.
  • Mass down, frequency down: each disc adds 24.1 g. Discs stack on the crown inside the cup (Ø26 bore on the hub boss) and are held by three M3 screws into the crown's tapped holes: 1 disc M3 × 8, 2 discs M3 × 12, 3 discs M3 × 16, 4 discs M3 × 20 (always 4 mm of thread in the crown; the heads stay inside the cup).
  • Spring down: the soft leaf is the 0.8 leaf's outline at 0.5 thick, 1135 N/m against 4426 N/m axially (stiffness goes with thickness cubed). Fit both leaves soft, each between two 0.6 half gaskets (0.6 + 0.5 + 0.6 = 1.7, the joint). One leaf per joint is the rule: two leaves in one joint would rub on each other, and a joint holds only 1.7. In the open-frame module each soft leaf sits on a 0.3 rim shim in the 0.8 seat.
  • Spring up: charge. With face B closed the bounce gas is the stiffest spring in the module: 3.0 kN/m at 1 bar air, 29.6 kN/m at 10 bar air, 35.3 kN/m at 10 bar helium (155 cm³ behind the piston). A stock 2 in spool between face B and the cap adds volume and softens it (k_b falls in proportion).
  • The table is the module alone. On an engine the working gas on face A adds its own stiffness (and the engine's power): the module's frequency on the engine is the engine's, and it is measured, not set.
  • Open-frame module: no bounce space, so the leaves and the mass are the whole module spring: 15.8 Hz with the 0.8 leaves and no disc, 15.0 Hz with four discs, 8.0 Hz on the soft leaves (moving mass 899 g, its tube rod is longer). The engine's own gas on face A adds to it; the datasheet lists that for engine volumes from 50 to 400 cm³.

Mass discs, 0.5 mm flexure leaf and rim shim for 2 in tri-clamp… size chart

discsmass (g)std open Hzstd air1 Hzstd air10 Hzstd He10 Hzsoft open Hzsoft air1 Hzsoft He10 Hz
086516.118.633.635.98.212.433.2
188915.918.433.135.58.112.332.8
291315.718.132.735.07.912.132.3
393715.517.932.234.57.812.031.9
496115.317.731.834.17.711.831.5

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
boreØ26piston cup hub bossslidela-mass-disc*
ODØ41piston cup skirt bore Ø42 (0.5 radial gap, no contact)designedla-mass-disc*
holes3 × Ø3.4 on r 17M3 clearance (ISO 273 medium)designedla-mass-disc*
rimØ64 × 0.5, clamped from Ø47.5 outtwo 0.6 half gaskets in the joint; centred on the Ø64 flange rims by the clampclampleaf-2in-piston-t0.5*
hub boreØ18tube rod, hub clamped by two collarsslideleaf-2in-piston-t0.5*
armsthree spiral arms inside Ø47.5free (no contact)designedleaf-2in-piston-t0.5*
rimØ64 × 0.5 on a 0.3 shim (open frame)open frame's Ø64 × 0.8 leaf seat under a clamp ringclampleaf-2in-piston-t0.5*
ODØ64open frame's Ø64 leaf seat (under a 0.5 leaf's rim)clampla-rim-shim*
faces0.3 thick, Ø47.5–Ø64seat floor and the 0.5 leaf's rimclampla-rim-shim*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

Xem Studiotools/gen_la_module.py: the module's geometry, masses, bounce volume, natural frequencies and every number on these pagescodeCC BY 4.0
Xem Studiotools/gen_fpse_gen.py: the free-piston generator whose stator, magnets, leaves and collars this module reuses; its leaf frame model and magnetic-circuit estimatecodeCC BY 4.0
Long Earth SocietyEngine buildsweb, videoLES site

Free files

★ Free files 3 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
la-mass-disc-41x26x4add-on mass disc Ø41 / Ø26 × 4, 3 × Ø3.4 on r 17: up to 4 stack on the cup's crown inside its skirt, 24.1 g each at 7.9 g/cm³STEP · STL
leaf-2in-piston-t0.5soft leaf: the 0.8 piston leaf's outline (Ø64 rim, Ø18 hub bore, 3 arms 4 wide sweeping 330°) at 0.5 thick; clamped between two 0.6 half gaskets (closed module) or on a 0.3 rim shim in the open frame's 0.8 seatSTEP · STL
la-rim-shim-64x0.3rim shim Ø64 / Ø47.5 × 0.3: under a 0.5 soft leaf's rim in the open frame's Ø64 × 0.8 leaf seat, so the clamp ring clamps it as it clamps a 0.8 leafSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=flexure-mass-discs-and-shims-2in

Mass discs, 0.5 mm flexure leaf and rim shim for 2 in tri-clamp flexures, isometric render of a generated part
Render of leaf-2in-piston-t0.5 from the free STEP; not to scale.

Fits with

Questions

Which way does each change go?

Discs lower the frequency; soft leaves lower it (most at 1 bar, little at 10 bar where the bounce gas dominates); more charge or less bounce volume raise it.

Is the soft leaf strong enough?

Its bending stress is 114 MPa at ±6 mm against 177 MPa for the 0.8 leaf: lower, because it is thinner.