Snap tri-clamp, bolt-free (printable, ½ to 10 in) — dimension sheet Source: Xem Studio, https://xemstudio.com/objects/snap-tri-clamp-bolt-free/ (sheet CC BY 4.0) Basis: Xem Studio design (v7, 6–10 in v8), tested on a 2 in printed joint Catalog version: 2026-10-20 Sizes: see table below - A tri-clamp clamp with no bolt: each piece carries a flush arm whose hooked claw drops into a notch on the next piece only when the two meet — clipped or not, nothing in between. Open with a butter knife in the V at the arm tip. - ½ to 8 in: two identical halves. 10 in: three identical 120° segments, because a 10 in half is wider than a 256 mm bed; each segment has one arm and one notch, the same latch. - Prints flat with no supports: every downward face is 45° or steeper, both outer edges carry the same R7 round. Every file fits a 256 × 256 mm bed as exported; the footprint column is one piece as it lies on the bed. - Sized for the printable 45° tri-clamp ferrules and a standard silicone gasket (closes on a 2.0 mm compressed stack). One clamp per flange: ½ and ¾ in share the 25 mm flange, 1 and 1½ in the 50.5 mm flange. - 6, 8 and 10 in carry more gasket force, so the wall, the band width and the arm thickness grow with the square root of the flange diameter (from the 4 in values); the claw, the groove and the knife V are the same as on the tested 2 in clamp, so one clamp key opens every size. - The STEP/STL pack (all sizes, ½ to 10 in) is $3 by card, or $2.40 for AI agents paying with x402 at /api/buy/snap-tri-clamp-pack. The dimension sheet is free. size pieces clamp OD width wall print footprint (one piece) ½–¾ in (25 mm flange) 2 halves 43.0 mm 16.0 mm 8.0 mm 42.3 × 26.4 mm 1–1½ in (50.5 mm flange) 2 halves 68.5 mm 22.5 mm 8.0 mm 67.4 × 42.2 mm 2 in (64 mm flange) 2 halves 82.0 mm 23.3 mm 8.0 mm 80.7 × 50.6 mm 2½ in (77.5 mm flange) 2 halves 95.5 mm 24.1 mm 8.0 mm 94.0 × 59.0 mm 3 in (91 mm flange) 2 halves 109.0 mm 24.9 mm 8.0 mm 107.3 × 67.4 mm 4 in (119 mm flange) 2 halves 137.0 mm 27.5 mm 8.0 mm 134.9 × 84.8 mm 6 in (166.9 mm flange) 2 halves 187.8 mm 32.6 mm 9.5 mm 185.7 × 113.3 mm 8 in (217.7 mm flange) 2 halves 241.3 mm 37.2 mm 10.8 mm 239.1 × 142.9 mm 10 in (268.5 mm flange) 3 segments (120°) 294.5 mm 41.3 mm 12.0 mm 218.5 × 172.1 mm Files elsewhere (not hosted by Xem Studio; license as stated by the publisher): - Xem Studio: Snap tri-clamp design — web — Publisher's page; dimensions are facts — https://xemstudio.com/ No true-size file yet: the published figures do not fix the whole shape; a measured scan is planned. API: https://xemstudio.com/api/geometry?object=snap-tri-clamp-bolt-free