Library › Hardware › Fasteners ·

Heat-set threaded inserts, ruthex RX series: M2 to M8 and #2-56 to 3/8-16

What hole does a ruthex M3 insert need? · Standard part · basis: ruthex RX series datasheet (d1 insert Ø, d2 tip Ø, L, W min wall, d3 hole Ø); geometry drawn by Xem Studio from those numbers

Also called: ruthex insert dimensions, ruthex m3 hole size, rx-m3x5.7, ruthex threaded insert stl

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
17 in table

Notes

  • Drawn as: lead-in pilot at the tip Ø over the bottom 15 % of the length, two knurl bands at the insert Ø with a relief groove between, thread as a plain bore at the minor diameter (threads not modelled). Knurl texture is not drawn: the insert Ø is the knurl's outside.
  • Print the hole at the listed hole Ø, at least the insert length + 1 mm deep for a blind hole (room for displaced plastic), and keep at least W of wall around it. Press the insert in with a soldering iron and insert tip at the plastic's printing temperature until its top is flush.

Heat-set threaded inserts, ruthex RX series: M2 to M8 and #2-56 to… size chart

articlethreadlength (mm)insert od (mm)tip (mm)hole (mm)min wall (mm)
RX-M2x4M24.03.63.13.21.3
RX-M2.5x5.7M2.55.74.63.94.01.6
RX-M3Sx4.0M34.04.63.94.01.6
RX-M3x5x4M34.05.04.254.41.3
RX-M3x5.7M35.74.63.94.01.6
RX-M4Sx4.0M44.06.35.55.62.1
RX-M4x8.1M48.16.35.55.62.1
RX-M5Sx5.8M55.87.16.36.42.6
RX-M5x9.5M59.57.16.36.42.6
RX-M6x12.7M612.78.77.98.03.3
RX-M8x12.7M812.710.19.59.64.5
RX-2-56x4#2-564.03.63.13.21.3
RX-4-40x5.7#4-405.74.63.94.01.6
RX-8-32x8.1#8-328.16.35.55.62.1
RX-10-24x9.5#10-249.57.16.36.42.6
RX-1/4-20x12.71/4-2012.78.77.98.03.3
RX-3/8-16x12.73/8-1612.712.611.811.96.0

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
insert OD / tipM2 Ø3.6 / 3.1; M2.5 4.6 / 3.9; M3 4.6 / 3.9 (5.0 / 4.25 for M3x5x4); M4 6.3 / 5.5; M5 7.1 / 6.3; M6 8.7 / 7.9; M8 10.1 / 9.5; 3/8-16 12.6 / 11.8install hole: M2 Ø3.2; M2.5 4.0; M3 4.0 (M3x5x4 4.4); M4 5.6; M5 6.4; M6 8.0; M8 9.6; inch #2-56 3.2, #4-40 4.0, #8-32 5.6, #10-24 6.4, 1/4-20 8.0, 3/8-16 11.9designedinsert-rx-*
depth and walllength 4.0 to 12.7; min wall 1.3 / 1.6 / 2.1 / 2.6 / 3.3 / 4.5 / 6.0blind hole at least insert length + 1 deep; wall around the hole at least Wdesignedinsert-rx-*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

ruthexRX series product datasheet: d1 insert Ø, d2 tip Ø, L, W min wall, d3 hole Ø (metric and UNC)PDFmaker's sheet; dimensions cited, nothing copied

Free files

★ Free files 17 parts. Generated by Xem Studio from the standard; threads are plain cylinders at major diameter. CC BY 4.0. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
insert-rx-m2x4ruthex RX-M2x4: M2, Ø3.6 knurl, tip Ø3.1, 4 long; print hole Ø3.2 × ≥5, wall ≥ 1.3STEP · STL
insert-rx-m2_5x5_7ruthex RX-M2.5x5.7: M2.5, Ø4.6 knurl, tip Ø3.9, 5.7 long; print hole Ø4 × ≥6.7, wall ≥ 1.6STEP · STL
insert-rx-m3sx4_0ruthex RX-M3Sx4.0: M3, Ø4.6 knurl, tip Ø3.9, 4 long; print hole Ø4 × ≥5, wall ≥ 1.6STEP · STL
insert-rx-m3x5x4ruthex RX-M3x5x4: M3, Ø5 knurl, tip Ø4.25, 4 long; print hole Ø4.4 × ≥5, wall ≥ 1.3STEP · STL
insert-rx-m3x5_7ruthex RX-M3x5.7: M3, Ø4.6 knurl, tip Ø3.9, 5.7 long; print hole Ø4 × ≥6.7, wall ≥ 1.6STEP · STL
insert-rx-m4sx4_0ruthex RX-M4Sx4.0: M4, Ø6.3 knurl, tip Ø5.5, 4 long; print hole Ø5.6 × ≥5, wall ≥ 2.1STEP · STL
insert-rx-m4x8_1ruthex RX-M4x8.1: M4, Ø6.3 knurl, tip Ø5.5, 8.1 long; print hole Ø5.6 × ≥9.1, wall ≥ 2.1STEP · STL
insert-rx-m5sx5_8ruthex RX-M5Sx5.8: M5, Ø7.1 knurl, tip Ø6.3, 5.8 long; print hole Ø6.4 × ≥6.8, wall ≥ 2.6STEP · STL
insert-rx-m5x9_5ruthex RX-M5x9.5: M5, Ø7.1 knurl, tip Ø6.3, 9.5 long; print hole Ø6.4 × ≥10.5, wall ≥ 2.6STEP · STL
insert-rx-m6x12_7ruthex RX-M6x12.7: M6, Ø8.7 knurl, tip Ø7.9, 12.7 long; print hole Ø8 × ≥13.7, wall ≥ 3.3STEP · STL
insert-rx-m8x12_7ruthex RX-M8x12.7: M8, Ø10.1 knurl, tip Ø9.5, 12.7 long; print hole Ø9.6 × ≥13.7, wall ≥ 4.5STEP · STL
insert-rx-2-56x4ruthex RX-2-56x4: #2-56, Ø3.6 knurl, tip Ø3.1, 4 long; print hole Ø3.2 × ≥5, wall ≥ 1.3STEP · STL
insert-rx-4-40x5_7ruthex RX-4-40x5.7: #4-40, Ø4.6 knurl, tip Ø3.9, 5.7 long; print hole Ø4 × ≥6.7, wall ≥ 1.6STEP · STL
insert-rx-8-32x8_1ruthex RX-8-32x8.1: #8-32, Ø6.3 knurl, tip Ø5.5, 8.1 long; print hole Ø5.6 × ≥9.1, wall ≥ 2.1STEP · STL
insert-rx-10-24x9_5ruthex RX-10-24x9.5: #10-24, Ø7.1 knurl, tip Ø6.3, 9.5 long; print hole Ø6.4 × ≥10.5, wall ≥ 2.6STEP · STL
insert-rx-1-4-20x12_7ruthex RX-1/4-20x12.7: 1/4-20, Ø8.7 knurl, tip Ø7.9, 12.7 long; print hole Ø8 × ≥13.7, wall ≥ 3.3STEP · STL
insert-rx-3-8-16x12_7ruthex RX-3/8-16x12.7: 3/8-16, Ø12.6 knurl, tip Ø11.8, 12.7 long; print hole Ø11.9 × ≥13.7, wall ≥ 6STEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=heat-set-inserts-ruthex

Heat-set threaded inserts, ruthex RX series: M2 to M8 and #2-56 to 3/8-16, isometric render of a generated part
Render of insert-rx-m5x9_5 from the free STEP; not to scale.

Fits with

Questions

ruthex M3 × 5.7 hole?

Ø4.0 (same as CNC Kitchen's M3 × 5.7), 1.6 wall.