Library › Hardware › Gears, cranks & flywheels ·
Ground rods, hollow rods and crank shafts: Ø6, Ø8 and Ø10 / 7
What precision rods and shafts are drawn for tri-clamp crosshead parts? · Hardware · basis: Design values; lengths from the engines' layouts
Also called: stirling rod lengths, hollow piston rod
Long Earth Society build part. Rods and shafts of my performance engines. Long Earth Society
Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features
- sizes
- 9 in table
Notes
- Ground rods cut to length with threaded ends (threads drawn at the major diameter): the displacer rods (Ø6, M6), the gamma's piston rod (Ø8, M8), the beta's hollow piston rod (Ø10 / Ø7, M10 × 1; the displacer rod runs inside it) and the Ø8 crank shafts the built-up cranks are pressed onto.
Ground rods, hollow rods and crank shafts: Ø6, Ø8 and Ø10 / 7 size chart
| part | size |
|---|---|
| rod-6x423.2-m6 | Ø6 × 423.20 |
| rod-8x306.25-m8 | Ø8 × 306.25 |
| rod-6x300.25-m6 | Ø6 × 300.25 |
| tube-10x7x160-m10x1 | Ø10/7 × 160.00 |
| shaft-8x56.5 | Ø8 × 56.50 |
| shaft-8x88 | Ø8 × 88.00 |
| shaft-8x46.3 | Ø8 × 46.30 |
| shaft-8x103.95 | Ø8 × 103.95 |
| shaft-8x138.3 | Ø8 × 138.30 |
Mating features
Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.
| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| displacer rods | Ø6, M6 × 12 ends | gland bushings (run), cap and yoke M6 holes | run | rod-6x* |
| piston rod | Ø8, M8 × 12 ends | gland bushings 8 × 12 × 20 (run) | run | rod-8x* |
| hollow rod | Ø10 / Ø7, M10 × 1 × 16 ends | guide bushings 10 × 14 × 15 (run); Ø6 displacer rod inside (no contact) | run | tube-10x7* |
| crank shafts | Ø8 | crank webs (press), 608 bores, collars, flywheel, pulley | press | shaft-8x* |
| transfer tube | Ø12.7 × 0.89 | 1/2 in tube compression fittings | designed | transfer-tube* |
Where the files are
Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.
| Long Earth Society | Engine builds | web, video | LES site |
Free files
★ Free files 13 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json
Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.
Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp- Claude: Add to Claude
- ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
- Cursor: install with one click. VS Code: install with one click.
| rod-6x423.2-m6 | Ø6 × 423.20 ground rod: horizontal gamma displacer rod, M6 × 12 both ends (drawn at Ø6) | STEP · STL |
| rod-8x306.25-m8 | Ø8 × 306.25 ground rod: horizontal gamma piston rod, M8 × 12 both ends | STEP · STL |
| rod-6x300.25-m6 | Ø6 × 300.25 ground rod: charged beta displacer rod, M6 × 12 both ends | STEP · STL |
| rod-6x315.4-m6 | Ø6 × 315.40 ground rod: walking-beam gamma displacer rod, M6 × 12 both ends | STEP · STL |
| transfer-tube-12.7x0.89x64 | transfer tube Ø12.7 × 0.89 wall × 64 (1/2 in tube) between the two 1/2 NPT fittings | STEP · STL |
| tube-10x7x160-m10x1 | hollow piston rod Ø10 / Ø7 × 160.00, M10 × 1 × 16 both ends (drawn at Ø10) | STEP · STL |
| shaft-8x56.5 | Ø8 × 56.50 crank shaft (pressed into the webs) | STEP · STL |
| shaft-8x88 | Ø8 × 88.00 crank shaft (pressed into the webs) | STEP · STL |
| shaft-8x46.3 | Ø8 × 46.30 crank shaft (pressed into the webs) | STEP · STL |
| shaft-8x103.95 | Ø8 × 103.95 crank shaft (pressed into the webs) | STEP · STL |
| shaft-8x138.3 | Ø8 × 138.30 crank shaft (pressed into the webs) | STEP · STL |
| shaft-8x95.8 | Ø8 × 95.80 crank shaft (pressed into the webs) | STEP · STL |
| shaft-8x91 | Ø8 × 91.00 crank shaft (twin: both webs pressed on it) | STEP · STL |
https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.Plain text: sheet.txt · JSON: /api/geometry?object=precision-rods-and-crank-shafts

Fits with
Questions
Why a hollow piston rod?
In the beta the displacer rod runs inside it, coaxial.
