Library › 3D printable tri-clamp › Clamps & fittings ·

Printable tri-clamp (45°): 90° and 45° elbows, ½ to 4 in

Can I 3D print tri-clamp elbows? · Hardware · basis: Xem Studio design: standard 2CMP / 2KMP centre-to-face and radius per size, 45° rims

Also called: printable tri clamp elbow, 3d printed sanitary elbow, 3d printed tri clamp, 3d printable tri clamp, tri clamp stl, printable tri clover

Exact dimensions. True size, with no tolerance added.

sizes
8 in table

Notes

  • 3D-printable tri-clamp: this is Xem Studio's print-friendly version of the standard sanitary fitting, drawn so it prints on an ordinary FDM or resin printer with no supports. Download the STL to print it, or the STEP to edit it. The files are true size (no printing allowance): add your own clearance in the slicer or CAD if your printer needs it.
  • Same layout dimensions as the standard elbows, so they swap into a planned run.
  • Printable tri-clamp: the ISO 2852 face and gasket groove are exactly standard, only the back cone behind each rim is 45° instead of 20°, so no rim overhangs more than 45° from vertical in any print orientation. Join these with the 45° clamps (printable-tri-clamp-clamps) and standard Type B gaskets; a 45° clamp fits only 45° rims, so keep a run all 45°. A 45° cone turns clamp force into face force at 1 : 1 (a 20° cone at 2.7 : 1), so tighten the clamp bolts harder or use M6.
  • Print orientation: straight parts face down; elbows, tees and crosses with one face down; horizontal bores bridge their top, so keep them small or add a light tree support inside.
  • Every clamp face is the ISO 2852 profile used across this site: 2.85 mm rim, flat face with the gasket groove (K 1.6 deep, R3 1.2 bottom, 23° walls, P2 0.8 edges) on C2, 20° back cone. Flange C3 / groove C2 / tube OD × wall, mm: ½–¾ in 25.0 / 20.4 (derived) / 12.7–19.05 × 1.65; 1–1½ in 50.5 / 43.5 / 25.4–38.1 × 1.65; 2 in 64.0 / 56.5 / 50.8 × 1.65; 2½ in 77.5 / 70.5 / 63.5 × 1.65; 3 in 91.0 / 83.5 / 76.2 × 1.65; 4 in 119.0 / 110.0 / 101.6 × 2.11; 6 in 166.9 (6.570 in) / 156.5 / 152.4 × 2.77; 8 in 217.7 (8.570 in) / 207.0 / 203.2 × 2.77; 10 in 268.5 / 261.0 / 254.0 × 3.40; 12 in 319.3 / 311.8 / 304.8 × 3.40.

Printable tri-clamp (45°): 90° and 45° elbows, ½ to 4 in size chart

size (in)c to f 90 (mm)c to f 45 (mm)radius (mm)
½41.324.528.6
¾41.324.528.6
150.828.638.1
1½69.836.557.1
288.944.476.2
2½107.952.495.2
3127.060.3114.3
4168.379.4152.4

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

GW KentTri-clamp fittings guide: tube OD, flange OD and ID per size to 12 in; solid cap thicknesswebpublisher's guide; dimensions cited
Rubber FabTri-Clamp gasket dimensional chart: gasket ID, OD and bead diameter per size (2 in bead 2.22 in / 56.50 mm, 1.5 in 1.71 / 43.50, 3 in 3.29 / 83.50)PDFmaker chart; dimensions are facts verify

Free files

★ Free files 16 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
elbow-90-45cone-0.5in½ in 90° elbow, 1.625 in centre to faceSTEP · STL
elbow-45-45cone-0.5in½ in 45° elbow, 0.966 in centre to faceSTEP · STL
elbow-90-45cone-0.75in¾ in 90° elbow, 1.625 in centre to faceSTEP · STL
elbow-45-45cone-0.75in¾ in 45° elbow, 0.966 in centre to faceSTEP · STL
elbow-90-45cone-1in1 in 90° elbow, 2.0 in centre to faceSTEP · STL
elbow-45-45cone-1in1 in 45° elbow, 1.125 in centre to faceSTEP · STL
elbow-90-45cone-1.5in1½ in 90° elbow, 2.75 in centre to faceSTEP · STL
elbow-45-45cone-1.5in1½ in 45° elbow, 1.437 in centre to faceSTEP · STL
elbow-90-45cone-2in2 in 90° elbow, 3.5 in centre to faceSTEP · STL
elbow-45-45cone-2in2 in 45° elbow, 1.75 in centre to faceSTEP · STL
elbow-90-45cone-2.5in2½ in 90° elbow, 4.25 in centre to faceSTEP · STL
elbow-45-45cone-2.5in2½ in 45° elbow, 2.063 in centre to faceSTEP · STL
elbow-90-45cone-3in3 in 90° elbow, 5.0 in centre to faceSTEP · STL
elbow-45-45cone-3in3 in 45° elbow, 2.375 in centre to faceSTEP · STL
elbow-90-45cone-4in4 in 90° elbow, 6.625 in centre to faceSTEP · STL
elbow-45-45cone-4in4 in 45° elbow, 3.125 in centre to faceSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=printable-tri-clamp-elbows

Printable tri-clamp (45°): 90° and 45° elbows, ½ to 4 in, isometric render of a generated part
Render of elbow-90-45cone-2in from the free STEP; not to scale.

Fits with

Questions

Can I 3D print this?

Yes. It is the 3D-printable version: every overhang is 45° or steeper, so it prints without supports, and the sealing face is standard ISO 2852, so a normal gasket and clamp fit.

Same size as a steel elbow?

Yes: centre to face and bend radius are the standard values.