Library › Tri-clamp & pipe › Pipe, tube & threads ·
SAE 45° flare fittings: tube OD, thread (5/16-24 to 1-1/4-12), nut hex and length, 1/8 to 7/8 in
What thread and nut size does an SAE 45 degree flare fitting have for each tube OD? · Standard part · basis: Parker Hannifin catalogue 3501E (41FL, 41FS) and SC Fastening nut pages, thread list checked on McMaster-Carr; SAE J512 / J513 not read; McMaster-Carr linked for CAD
Also called: sae 45 flare thread size, 1/4 flare nut thread, 7/16-20 flare, 3/8 flare nut thread 5/8-18, flare nut hex size, 1/2 flare 3/4-16, 45 degree flare dimensions, sae flare vs an, flare fitting thread chart, 5/8 flare 7/8-14, flare nut stl, flare nut length, flare fitting tube od thread, sae 45 flare wrench size, 1/4 flare nut wrench size
Exact dimensions. True size, with no tolerance added.
- sizes
- 9 in table
Notes
- SAE 45° flare (the tube end is flared to 45°, the nut pulls it against a male cone). The size name is the TUBE OD; the dash number is the tube OD in sixteenths of an inch (-4 = 1/4 in tube). Threads are straight UNF: 1/8 in tube 5/16-24, 3/16 in 3/8-24, 1/4 in 7/16-20, 5/16 in 1/2-20, 3/8 in 5/8-18, 1/2 in 3/4-16, 5/8 in 7/8-14, 3/4 in 1-1/16-14, 7/8 in 1-1/4-12. These match Parker's catalogue for every size and the thread list on McMaster-Carr's 45° flared fittings page. The governing standards are SAE J512 and J513; their text is paywalled and was not read.
- Do not mix with 37° (AN / JIC) or with compression nuts: 1/4 in flare is 7/16-20 (this page), 1/4 in compression is 7/16-24, and the 37° AN -4 is also 7/16-20 with a different seat. See 'an-jic-37-degree-flare-fittings' for 37°. A 7/16-20 nut cross-threads on a 7/16-24 fitting, and 45° and 37° seats leak against each other.
- Numbers: Parker catalogue 3501E (long nut 41FL and short nut 41FS / 41FX, pages H4-H10, read through a SlideShare copy): hex c, length l and a dimension 'd' that Parker's page labels without a definition (it is the tube OD plus about 0.007 in); the 41FX 'shorter' nut (3/8 l 0.91, 1/2 l 1.00, 5/8 l 1.06, 3/4 l 1.17) is not tabulated. SC Fastening's catalogue pages give an independent set for a short rod nut (A = length, hex): its A and hex equal Parker's short nut for 1/8, 3/16, 1/4, 5/16 in (hex 0.37 vs 3/8 and so on is rounding); its long forged nut differs from Parker's long nut (1/4 in hex 0.62 vs 9/16, 3/8 in A 1.06 vs l 1.31), so both are shown rather than merged. Dash sizes follow Parker's part numbers (41FS-2 to 41FS-14).
- Files (17): hex envelopes of Parker's short nut (9 sizes) and long nut (8 sizes): hex across flats c, length l, a through hole at the tube OD. No internal thread, no 45° seat, no tube relief, because none is published; the thread size is in the file name only. The dimension the nut screws onto (male thread, 45° cone, flare diameter) is not published in a readable table, so no fitting body is drawn.
- Left out: flare diameters and the 45° flare envelope (SAE J533 / J512 values were not readable here; the 37° page lists J533 ranges), male and female connector bodies, elbows and tees (A, B, C columns of the catalogues could not be matched to the drawings), hose sizes, working pressures, and the Parker 41FX shorter nut. McMaster-Carr's category (linked) offers per-part STEP / IGES.
SAE 45° flare fittings: tube OD, thread (5/16-24 to 1-1/4-12), nut… size chart
| dash size | tube OD, in (mm) | nut thread, UNF (major, mm) | Parker short nut 41FS: hex / length l, in | Parker long nut 41FL: hex / length l, in | Parker d, in | SC Fastening short rod nut: A / hex, in | SC Fastening long forged nut: A / hex, in |
|---|---|---|---|---|---|---|---|
| -2 | 1/8 (3.17) | 5/16-24 (major 7.94) | 3/8 / 0.50 | 3/8 / 0.75 | 0.133 | 0.50 / 0.37 | — |
| -3 | 3/16 (4.76) | 3/8-24 (major 9.52) | 7/16 / 0.62 | 7/16 / 0.81 | 0.195 | 0.62 / 0.43 | — |
| -4 | 1/4 (6.35) | 7/16-20 (major 11.11) | 9/16 / 0.75 | 9/16 / 0.94 | 0.257 | 0.75 / 0.56 | 0.94 / 0.62 |
| -5 | 5/16 (7.94) | 1/2-20 (major 12.70) | 5/8 / 0.88 | 5/8 / 1.12 | 0.320 | 0.88 / 0.62 | — |
| -6 | 3/8 (9.52) | 5/8-18 (major 15.88) | 3/4 / 1.00 | 3/4 / 1.31 | 0.382 | — | 1.06 / 0.81 |
| -8 | 1/2 (12.70) | 3/4-16 (major 19.05) | 7/8 / 1.12 | 7/8 / 1.62 | 0.507 | — | 1.19 / 0.94 |
| -10 | 5/8 (15.88) | 7/8-14 (major 22.22) | 1-1/16 / 1.31 | 1-1/16 / 1.88 | 0.632 | — | 1.44 / 1.06 |
| -12 | 3/4 (19.05) | 1-1/16-14 (major 26.99) | 1-1/4 / 1.50 | 1-1/4 / 2.19 | 0.757 | — | 1.75 / 1.31 |
| -14 | 7/8 (22.22) | 1-1/4-12 (major 31.75) | 1-1/2 / 1.62 | — | 0.882 | — | — |
Where the files are
Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.
| Parker Hannifin (catalog 3501E, hosted on SlideShare) | 45 degree flare fittings, pages H4-H10: 41FL long nut and 41FS / 41FX short nut: thread, hex c, d, length l | web | Publisher's page; dimensions are facts |
| SC Fastening (JB-style catalogue) | SAE 45 flare short rod nut: tube OD, thread, A, hex | web | Publisher's page; dimensions are facts |
| SC Fastening (JB-style catalogue) | SAE 45 flare long forged nut: tube OD, thread, A, hex | web | Publisher's page; dimensions are facts |
| McMaster-Carr | 45-degree flared tube fittings (free STEP/IGES per part, for your own design use; no redistribution) | STEP, IGES, PDF | McMaster-Carr site terms: personal design use, no redistribution verify |
Free files
★ Free files 17 parts. Generated by Xem Studio from the standard; threads are plain cylinders at major diameter. CC BY 4.0. index.json
Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.
Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp- Claude: Add to Claude
- ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
- Cursor: install with one click. VS Code: install with one click.
| flare-nut-short-41fs-2-tube-1-8in-5-16-24 | SAE 45° flare short nut envelope (Parker 41FS-2): hex 3/8 in across flats × 0.50 in long, tube bore Ø3.17 mm (= 1/8 in tube OD); thread 5/16-24 is on the part but NOT drawn (internal thread depth and the 45° seat are not published); Parker's d column (0.133 in) is not used | STEP · STL |
| flare-nut-long-41fl-2-tube-1-8in-5-16-24 | SAE 45° flare long nut envelope (Parker 41FL-2): hex 3/8 in across flats × 0.75 in long, tube bore Ø3.17 mm (= 1/8 in tube OD); thread 5/16-24 is on the part but NOT drawn | STEP · STL |
| flare-nut-short-41fs-3-tube-3-16in-3-8-24 | SAE 45° flare short nut envelope (Parker 41FS-3): hex 7/16 in across flats × 0.62 in long, tube bore Ø4.76 mm (= 3/16 in tube OD); thread 3/8-24 is on the part but NOT drawn (internal thread depth and the 45° seat are not published); Parker's d column (0.195 in) is not used | STEP · STL |
| flare-nut-long-41fl-3-tube-3-16in-3-8-24 | SAE 45° flare long nut envelope (Parker 41FL-3): hex 7/16 in across flats × 0.81 in long, tube bore Ø4.76 mm (= 3/16 in tube OD); thread 3/8-24 is on the part but NOT drawn | STEP · STL |
| flare-nut-short-41fs-4-tube-1-4in-7-16-20 | SAE 45° flare short nut envelope (Parker 41FS-4): hex 9/16 in across flats × 0.75 in long, tube bore Ø6.35 mm (= 1/4 in tube OD); thread 7/16-20 is on the part but NOT drawn (internal thread depth and the 45° seat are not published); Parker's d column (0.257 in) is not used | STEP · STL |
| flare-nut-long-41fl-4-tube-1-4in-7-16-20 | SAE 45° flare long nut envelope (Parker 41FL-4): hex 9/16 in across flats × 0.94 in long, tube bore Ø6.35 mm (= 1/4 in tube OD); thread 7/16-20 is on the part but NOT drawn | STEP · STL |
| flare-nut-short-41fs-5-tube-5-16in-1-2-20 | SAE 45° flare short nut envelope (Parker 41FS-5): hex 5/8 in across flats × 0.88 in long, tube bore Ø7.94 mm (= 5/16 in tube OD); thread 1/2-20 is on the part but NOT drawn (internal thread depth and the 45° seat are not published); Parker's d column (0.320 in) is not used | STEP · STL |
| flare-nut-long-41fl-5-tube-5-16in-1-2-20 | SAE 45° flare long nut envelope (Parker 41FL-5): hex 5/8 in across flats × 1.12 in long, tube bore Ø7.94 mm (= 5/16 in tube OD); thread 1/2-20 is on the part but NOT drawn | STEP · STL |
| flare-nut-short-41fs-6-tube-3-8in-5-8-18 | SAE 45° flare short nut envelope (Parker 41FS-6): hex 3/4 in across flats × 1.00 in long, tube bore Ø9.52 mm (= 3/8 in tube OD); thread 5/8-18 is on the part but NOT drawn (internal thread depth and the 45° seat are not published); Parker's d column (0.382 in) is not used | STEP · STL |
| flare-nut-long-41fl-6-tube-3-8in-5-8-18 | SAE 45° flare long nut envelope (Parker 41FL-6): hex 3/4 in across flats × 1.31 in long, tube bore Ø9.52 mm (= 3/8 in tube OD); thread 5/8-18 is on the part but NOT drawn | STEP · STL |
| flare-nut-short-41fs-8-tube-1-2in-3-4-16 | SAE 45° flare short nut envelope (Parker 41FS-8): hex 7/8 in across flats × 1.12 in long, tube bore Ø12.70 mm (= 1/2 in tube OD); thread 3/4-16 is on the part but NOT drawn (internal thread depth and the 45° seat are not published); Parker's d column (0.507 in) is not used | STEP · STL |
| flare-nut-long-41fl-8-tube-1-2in-3-4-16 | SAE 45° flare long nut envelope (Parker 41FL-8): hex 7/8 in across flats × 1.62 in long, tube bore Ø12.70 mm (= 1/2 in tube OD); thread 3/4-16 is on the part but NOT drawn | STEP · STL |
| flare-nut-short-41fs-10-tube-5-8in-7-8-14 | SAE 45° flare short nut envelope (Parker 41FS-10): hex 1-1/16 in across flats × 1.31 in long, tube bore Ø15.88 mm (= 5/8 in tube OD); thread 7/8-14 is on the part but NOT drawn (internal thread depth and the 45° seat are not published); Parker's d column (0.632 in) is not used | STEP · STL |
| flare-nut-long-41fl-10-tube-5-8in-7-8-14 | SAE 45° flare long nut envelope (Parker 41FL-10): hex 1-1/16 in across flats × 1.88 in long, tube bore Ø15.88 mm (= 5/8 in tube OD); thread 7/8-14 is on the part but NOT drawn | STEP · STL |
| flare-nut-short-41fs-12-tube-3-4in-1-1-16-14 | SAE 45° flare short nut envelope (Parker 41FS-12): hex 1-1/4 in across flats × 1.50 in long, tube bore Ø19.05 mm (= 3/4 in tube OD); thread 1-1/16-14 is on the part but NOT drawn (internal thread depth and the 45° seat are not published); Parker's d column (0.757 in) is not used | STEP · STL |
| flare-nut-long-41fl-12-tube-3-4in-1-1-16-14 | SAE 45° flare long nut envelope (Parker 41FL-12): hex 1-1/4 in across flats × 2.19 in long, tube bore Ø19.05 mm (= 3/4 in tube OD); thread 1-1/16-14 is on the part but NOT drawn | STEP · STL |
| flare-nut-short-41fs-14-tube-7-8in-1-1-4-12 | SAE 45° flare short nut envelope (Parker 41FS-14): hex 1-1/2 in across flats × 1.62 in long, tube bore Ø22.22 mm (= 7/8 in tube OD); thread 1-1/4-12 is on the part but NOT drawn (internal thread depth and the 45° seat are not published); Parker's d column (0.882 in) is not used | STEP · STL |
https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.Plain text: sheet.txt · JSON: /api/geometry?object=sae-45-degree-flare-nuts-and-threads

Fits with




Questions
What thread is a 1/4 in SAE 45° flare nut?
7/16-20 UNF. 3/8 in tube is 5/8-18, 1/2 in tube is 3/4-16, 5/8 in is 7/8-14, 3/4 in is 1-1/16-14.
What wrench fits a 3/8 in flare nut?
Parker's 3/8 in tube nut (5/8-18) has a 3/4 in hex; SC Fastening's long forged nut for the same tube lists 0.81 in.
Is a 45° flare the same as AN / JIC?
No: AN and JIC seal on a 37° flare. The 1/4 in sizes share 7/16-20 but the seats do not interchange.