Library › Tri-clamp & pipe › Inserts & liners ·

2 in tri-clamp bore spacers and liners: 9.8, 60 and 61.7 mm

What spacer sets a part at depth inside a 2 inch tri-clamp spool? · Hardware · basis: ASME BPE 2 in bore Ø47.5; ISO 2852 Type B lip 0.55 past the face; inside Ø44 = the regenerator cage bore; lengths from the engine layouts in tools/gen_ta_family.py

Also called: thermoacoustic spacer tube, thermal buffer tube liner, tri clamp bore spacer, regenerator spacer ring, heat exchanger spacer

Long Earth Society build part. The spacers that hold my thermoacoustic cores together. Long Earth Society

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
3 in table

Notes

  • Thin tubes at the spool bore (Ø47.5 outside, Ø44 inside) that stand between the parts of a thermoacoustic core and hold each one where the acoustic design wants it. Their ends bear on the exchangers' 1.0 mm outer ring and on the gasket lip, so the whole stack is held between the two gasket lips of the spool with nothing loose.
  • 9.8: from a gasket lip to an exchanger at 10.35 mm from the face, so the exchanger sits under a 14 mm water jacket that starts 9.35 mm from the face (clear of the clamp).
  • 61.7: the loop core's thermal buffer tube liner. In a 6 in spool the stack of parts is lip, 9.8 spacer, exchanger 10, buffer tube 61.7, hot exchanger 10, regenerator 40, exchanger 10, 9.8 spacer, lip: exactly the 151.3 mm between the two lips.
  • 60: the hot-cavity liner of the standing-wave engines' closed hot end; it holds the hot exchanger 60 mm off the closed end, which in the model lowers the half-wave engine's onset from about 680 °C (exchanger on the closed end) to about 271 °C.
  • Fits: outside slide in the bore; inside is gas passage; the end faces are flat rings.

2 in tri-clamp bore spacers and liners: 9.8, 60 and 61.7 mm size chart

fileoutside (mm)inside (mm)length (mm)use
ta-spacer-2in-9.847.544.09.8end spacer
ta-spacer-2in-6047.544.060.0hot-cavity liner
ta-spacer-2in-61.747.544.061.7thermal buffer tube

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
outsideØ47.52 in tri-clamp spool / head boreslideall
insideØ44gas passage (no contact)designedall
end facesflat ring Ø44–Ø47.5heat-exchanger outer ring, regenerator cage end, Type B gasket lipdesignedall
length8.4 / 60 / 61.7positions of the exchangers, stack and regenerator in the layoutdesignedall

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

Long Earth SocietyEngine buildsweb, videoLES site

Free files

★ Free files 3 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
ta-spacer-2in-9.8Ø47.5 / Ø44 × 9.8: end spacer: from the Type B gasket lip (0.55 inside the face) to an exchanger at 10.35STEP · STL
ta-spacer-2in-60Ø47.5 / Ø44 × 60: hot-cavity liner of the standing-wave head: closed end to the hot exchangerSTEP · STL
ta-spacer-2in-61.7Ø47.5 / Ø44 × 61.7: thermal buffer tube liner of the loop core: hot exchanger to the secondary ambient exchangerSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=tri-clamp-bore-spacers-2in

2 in tri-clamp bore spacers and liners: 9.8, 60 and 61.7 mm, isometric render of a generated part
Render of ta-spacer-2in-60 from the free STEP; not to scale.

Fits with

Questions

Why does the buffer tube have a liner?

It is what the hot exchanger and the regenerator stand on: without it they would slide down the empty buffer tube.

Do the spacers change the acoustics?

Slightly: the gas passage is Ø44 instead of Ø47.5 over their length; the model on the build lists includes it.