Library › Tri-clamp & pipe › Inserts & liners ·
Parallel-plate heat exchangers for 1.5, 2 and 3 in tri-clamp spools
What parallel-plate heat exchanger fits inside a tri-clamp spool? · Hardware · basis: Parallel-plate heat exchangers on both stack faces (Swift), plate gap and thickness equal to the spiral stack's channel; disc drawn at the 16 ga tri-clamp spool bore (1.5 in = 34.8 mm, 2 in = 47.5, 3 in = 72.9)
Also called: thermoacoustic heat exchanger, thermoacoustic engine heat exchanger dimensions, parallel plate heat exchanger stack, hot and cold heat exchanger thermoacoustic, thermoacoustic heat exchanger stl, tri clamp thermoacoustic heat exchanger
Long Earth Society build part. The hot and cold exchangers I drew for the stacks on this shelf. Long Earth Society
Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features
- sizes
- 3 in table
Notes
- A thermoacoustic stack only holds the temperature gradient; the heat exchangers on its two faces move heat into and out of the gas. The hot exchanger sits against the stack's hot face (the closed-end side of a λ/4 resonator), the cold one against the cold face, both inside the same spool bore.
- Each exchanger is a disc Ø34.8 / Ø47.5 / Ø72.9 (the 1.5 / 2 / 3 in spool bore, exact) × 10 mm long: a 1.0 mm outer ring holding parallel plates 0.4 mm thick at 1.4 mm pitch, one plate on the axis, 1.0 mm gas gaps between them. That is the spiral stack's 1.0 mm gap and 0.4 mm wall (stack-spiral-*-g1.0), so the gas channel keeps its width from stack to exchanger.
- The hot and cold files of a size are the same geometry; there are two so each stack face has its own. What they are made of, and how heat reaches the ring and plates, is the maker's choice: the file is the geometry.
- Exact dimensions: the disc OD is the spool bore with no allowance, listed under Mating features with its fit. Plate thickness, gap and ring width are design dimensions and stay as drawn.
- LES: I drew these for the stacks on this shelf: same spools, same 1.0 mm channel.
Parallel-plate heat exchangers for 1.5, 2 and 3 in tri-clamp spools size chart
| spool | bore mm (= exchanger OD) | length (mm) | ring (mm) | plate (mm) | gap (mm) | pitch (mm) | plates | open area pct |
|---|---|---|---|---|---|---|---|---|
| 1.5 | 34.8 | 10.0 | 1.0 | 0.4 | 1.0 | 1.4 | 23 | 63.5 |
| 2 | 47.5 | 10.0 | 1.0 | 0.4 | 1.0 | 1.4 | 33 | 65.5 |
| 3 | 72.9 | 10.0 | 1.0 | 0.4 | 1.0 | 1.4 | 51 | 67.5 |
Mating features
Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.
| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| exchanger OD | spool bore (34.8 / 47.5 / 72.9) | tri-clamp spool bore | socket | heat-exchanger-* |
| plates / gas gaps | 0.4 plates, 1.0 gaps, 1.4 pitch | stack channel (stack-spiral-*-g1.0) | designed | heat-exchanger-* |
| outer ring | 1.0 wall | holds the plates | designed | heat-exchanger-* |
Where the files are
Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.
| Wikipedia | Thermoacoustic heat engine | web | CC BY-SA 4.0 (text) |
| G. W. Swift (LANL) | Thermoacoustics: A Unifying Perspective for Some Engines and Refrigerators (textbook; DeltaEC software free) | web, software | LANL verify |
| Long Earth Society | Engine builds | web, video | LES site |
Free files
★ Free files 6 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json
Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.
Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp- Claude: Add to Claude
- ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
- Cursor: install with one click. VS Code: install with one click.
| heat-exchanger-hot-1.5in | hot heat exchanger for the 1.5 in spool: Ø34.8 × 10 disc (the spool bore, exact), 1 mm outer ring, 0.4 mm plates at 1.4 mm pitch with 1 mm gas gaps (the spiral stack's channel); goes on the hot face of the stack | STEP · STL |
| heat-exchanger-cold-1.5in | cold heat exchanger for the 1.5 in spool: Ø34.8 × 10 disc (the spool bore, exact), 1 mm outer ring, 0.4 mm plates at 1.4 mm pitch with 1 mm gas gaps (the spiral stack's channel); goes on the cold face of the stack | STEP · STL |
| heat-exchanger-hot-2in | hot heat exchanger for the 2 in spool: Ø47.5 × 10 disc (the spool bore, exact), 1 mm outer ring, 0.4 mm plates at 1.4 mm pitch with 1 mm gas gaps (the spiral stack's channel); goes on the hot face of the stack | STEP · STL |
| heat-exchanger-cold-2in | cold heat exchanger for the 2 in spool: Ø47.5 × 10 disc (the spool bore, exact), 1 mm outer ring, 0.4 mm plates at 1.4 mm pitch with 1 mm gas gaps (the spiral stack's channel); goes on the cold face of the stack | STEP · STL |
| heat-exchanger-hot-3in | hot heat exchanger for the 3 in spool: Ø72.9 × 10 disc (the spool bore, exact), 1 mm outer ring, 0.4 mm plates at 1.4 mm pitch with 1 mm gas gaps (the spiral stack's channel); goes on the hot face of the stack | STEP · STL |
| heat-exchanger-cold-3in | cold heat exchanger for the 3 in spool: Ø72.9 × 10 disc (the spool bore, exact), 1 mm outer ring, 0.4 mm plates at 1.4 mm pitch with 1 mm gas gaps (the spiral stack's channel); goes on the cold face of the stack | STEP · STL |
https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.Plain text: sheet.txt · JSON: /api/geometry?object=tri-clamp-parallel-plate-heat-exchangers

Fits with




Questions
What does a heat exchanger do in a thermoacoustic engine?
It moves heat into the gas at the stack's hot face and out of it at the cold face; the stack between them only holds the temperature gradient.
What plate spacing should a thermoacoustic heat exchanger have?
The same channel as the stack: here 1.0 mm gaps between 0.4 mm plates (1.4 mm pitch), matching the spiral stack's 1.0 mm gap and 0.4 mm sheet.
What size heat exchanger fits a 2 inch tri-clamp spool?
Ø47.5 × 10 mm, the 2 in spool bore exactly, with a 1.0 mm outer ring and 0.4 mm plates at 1.4 mm pitch. The 1.5 in is Ø34.8 and the 3 in Ø72.9, same plates and length.
Are the hot and cold heat exchangers different?
Not in shape: both files of a size are the same geometry, one for each face of the stack.