Library › Tri-clamp & pipe › Clamp fittings ·

10 in tri-clamp closed-end cup (welded floor)

What does a 10 inch closed-end tri-clamp cup look like? · Hardware · basis: Fabrication spec: an L14AM7-type 10 in ferrule end on Ø254 × 3.40 tube, closed by a 12.7 plate welded flush with the tube OD; exact geometry

Also called: 10 inch tri clamp hot end, welded bottom tri clamp spool, tri clamp pot stirling, htd stirling hot plate

Long Earth Society build part. Parts of the HTD engines. Long Earth Society

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
1 in table

Notes

  • The hot face is one piece: the floor is welded to the tube, so the only joint is the clamp at the top, 48 mm of tube wall above the flame (main HTD). That wall is also the engine's biggest heat leak: about 335 W conducted from a 450 °C floor to a 77 °C cap at 16 W/m·K (a lower-conductivity wall leaks proportionally less).
  • Floor: 12.7 thick. At the 6 bar gauge relief setting, treated as simply supported at the bore (conservative for a welded edge), it sees 70 MPa at the centre and bows 0.25 mm (Roark Table 11.2). The floor must be rated for that at its working temperature; I hold the hot face at or below 450 °C.
  • The cup's own ferrule face takes the standard 10 in gasket and clamp.

10 in tri-clamp closed-end cup size chart

partlength (mm)floor (mm)chamber face to floor (mm)
hot-cup-10in-60.460.412.747.7

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
faceISO 2852 10 ingasket-10in + 10 in clampclampall
boreØ247.19 to the floordisplacer Ø240 (3.6 radial, no contact)designedall
floor weldØ254 × 12.7 flush with the tube ODtube end (welded, sealed)designedall

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

Steel & O'BrienSanitary products catalog 2024: 16AMP end caps 10 / 12 in (A 0.480, B 10.570 / 12.570 in); L14AM7 ferrules 1.500 in; clamp ratings 13MHHM, 13MHP, 13ASMEPDFpublisher's catalogue; dimensions cited, nothing copied
Holland Applied TechnologiesSanitary tri-clamp fittings: EG14AM7 ferrules 8 / 10 / 12 in (1.500, bore 9.732 / 11.732 in, tube 10.000 / 12.000 in); EG16A caps (10.570 / 12.570 in)PDFpublisher's catalogue; dimensions cited, nothing copied
McGraw-HillYoung & Budynas, Roark's Formulas for Stress and Strain, 7th ed.: Table 8.1 (fixed–guided beam), Table 11.2 (circular plates under uniform pressure)bookformulas are facts verify
Long Earth SocietyEngine buildsweb, videoLES site

Free files

★ Free files 1 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
hot-cup-10in-60.410 in × 60.4 closed-end cup: ISO 2852 face, Ø254 × 3.40 tube, 12.7 floor welded flush (main HTD: chamber 51.0 face to floor with the cap)STEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=tri-clamp-closed-end-cup-10in

10 in tri-clamp closed-end cup (welded floor), isometric render of a generated part
Render of hot-cup-10in-60.4 from the free STEP; not to scale.

Fits with

Questions

Why a welded floor instead of a cap?

A cap would put a gasket and a clamp in the flame. With the floor welded on, the only joint sits up at the cold cap.