Library › Tri-clamp & pipe › Clamp fittings ·
2 in tri-clamp spools: 42 mm bored Ø48.00 and 25.4 mm (fabrication spec)
What short 2 inch tri-clamp spools can be ordered bored to 48 mm? · Hardware · basis: Fabrication specs on standard 2 in ferrules (ISO 2852 faces as gen_hardware draws them, BPE tube Ø50.8 × 1.65); lengths set by the module's stroke, the leaves' joints and two high-pressure clamps per spool
Also called: short tri clamp spool, custom length sanitary spool, tri clamp spool bored 48, 2 inch spool 25.4 mm, linear alternator module spool
Long Earth Society build part. The body of my clamp-in linear alternator module. Long Earth Society
Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features
- sizes
- 2 in table
Notes
- Two plain custom spools, both full 2 in sanitary fittings with a standard ferrule face at each end. With the catalog's stock 2 in × 3 in spool bored Ø48.00 between them they make the body of my linear alternator module: face A — 42 bored — leaf 1 — 3 in bored — leaf 2 — 25.4 — face B.
- 42 mm spool, bored: the bore opened from Ø47.5 to Ø48.00 end to end and finished as a running bore (wall 1.40). It is the piston's cylinder: the cup's 24 mm land runs in it as a clearance seal. Spec line: '2 in × 42 mm clamp × clamp spool, tube Ø50.8 × 1.65, bore finished Ø48.00 through'.
- 25.4 mm spool: two 0.5 in (12.7 mm) short weld ferrules welded back to back, nothing else: room for leaf 2's hub and collar to travel ±6 mm. Spec line: '2 in × 25.4 mm clamp × clamp spool, two short ferrules'.
- Both are as short as two high-pressure clamps side by side allow: each clamp needs about 10 mm either side of its joint plane. Hoop stress at the 15 bar gauge relief setting: 27.5 MPa in the 1.40 bored wall, 23.0 MPa in the plain tube; the builder checks that against what the spools are made of.
2 in tri-clamp spools: 42 mm bored Ø48.00 and 25.4 mm size chart
| spool | face to face (mm) | bore (mm) | wall (mm) | faces | made from |
|---|---|---|---|---|---|
| spool-2in-42mm-bored-48.00 | 42 | 48.00 (finished) | 1.4 | ISO 2852 2 in, both | two ferrules + tube, bored |
| spool-2in-25.4mm | 25.4 | 47.5 (as made) | 1.65 | ISO 2852 2 in, both | two 12.7 short weld ferrules |
Mating features
Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.
| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| bore | Ø48.00 × 42 | piston cup land Ø48.00 × 24 (clearance seal) | run | spool-2in-42mm-bored* |
| faces | ISO 2852 2 in, both ends | face A: Type B gasket + clamp to the engine; other face: half gaskets round leaf 1 (closed module) or Type B gasket + clamp to the open frame base | clamp | spool-2in-42mm-bored* |
| faces | ISO 2852 2 in, both ends | joint 2: half gaskets round leaf 2; face B: Type B gasket + clamp to the port cap or the next device | clamp | spool-2in-25.4mm* |
| bore | Ø47.5 (as made) | leaf 2's upper collar and the tube rod's end (no contact) | designed | spool-2in-25.4mm* |
Where the files are
Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.
| ISO (via iTeh sample) | ISO 2852 clamp liners: face profile and flange / groove diameters | standard excerpt; dimensions are facts | |
| ASME | BPE Bioprocessing Equipment (tube OD and wall, clamp fittings) | standard | ASME; dimensions are facts verify |
| Xem Studio | tools/gen_la_module.py: the module's geometry, masses, bounce volume, natural frequencies and every number on these pages | code | CC BY 4.0 |
| Long Earth Society | Engine builds | web, video | LES site |
Free files
★ Free files 2 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json
Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.
Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp- Claude: Add to Claude
- ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
- Cursor: install with one click. VS Code: install with one click.
| spool-2in-42mm-bored-48.00 | 2 in × 42 mm spool, ISO 2852 faces both ends, bore finished Ø48.00 end to end (wall 1.40): the module's piston cylinder, face A to the engine | STEP · STL |
| spool-2in-25.4mm | 2 in × 25.4 mm spool: two 12.7 mm short weld ferrules back to back, ISO 2852 faces, as-made Ø47.5 bore: the module's face B end | STEP · STL |
https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.Plain text: sheet.txt · JSON: /api/geometry?object=tri-clamp-spools-2in-bored-48

Fits with




Questions
Can I order these?
Yes: both are standard 2 in ferrules on standard tube; the bored spool then has its bore finished to Ø48.00 end to end, as the other bored spools on this site.
Which version uses which?
The 42 mm bored spool is in both versions of the module (closed and open frame); the 25.4 mm spool only in the closed one.
Why not a stock 3 in spool at each end?
It would work and add 85 mm of length; on the working side every extra millimetre is dead volume in the engine under test.