Library › 3D printable tri-clamp › Caps, lids & ports ·

Printable tri-clamp (45°): probe gland caps: Ø4, Ø6 and ¼ in probes, 1 to 3 per cap

How do I put a 6 mm temperature probe through a tri-clamp lid (3D printable)? · Hardware · basis: Xem Studio design: Xem Studio design on the standard solid cap: a boss bored to the probe diameter with two internal grooves for a probe-size × 1.5 O-ring; printable 45° back cone

Also called: tri clamp temperature probe port printable, ds18b20 tri clamp printable, 6mm probe gland printable, 3d printed tri clamp, 3d printable tri clamp, tri clamp stl, printable tri clover

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
18 in table

Notes

  • 3D-printable tri-clamp: this is Xem Studio's print-friendly version of the standard sanitary fitting, drawn so it prints on an ordinary FDM or resin printer with no supports. Download the STL to print it, or the STEP to edit it. The files are true size (no printing allowance): add your own clearance in the slicer or CAD if your printer needs it.
  • Slide a stainless probe (the common 6 × 50 mm DS18B20 temperature probe, a Ø4 thermocouple or a ¼ in RTD) down through the lid; two O-rings seal it and let you set the depth.
  • Printable tri-clamp: the ISO 2852 face and gasket groove are exactly standard, only the back cone behind each rim is 45° instead of 20°, so no rim overhangs more than 45° from vertical in any print orientation. Join these with the 45° clamps (printable-tri-clamp-clamps) and standard Type B gaskets; a 45° clamp fits only 45° rims, so keep a run all 45°. A 45° cone turns clamp force into face force at 1 : 1 (a 20° cone at 2.7 : 1), so tighten the clamp bolts harder or use M6.
  • Print orientation: straight parts face down; elbows, tees and crosses with one face down; horizontal bores bridge their top, so keep them small or add a light tree support inside.
  • Every clamp face is the ISO 2852 profile used across this site: 2.85 mm rim, flat face with the gasket groove (K 1.6 deep, R3 1.2 bottom, 23° walls, P2 0.8 edges) on C2, 20° back cone. Flange C3 / groove C2 / tube OD × wall, mm: ½–¾ in 25.0 / 20.4 (derived) / 12.7–19.05 × 1.65; 1–1½ in 50.5 / 43.5 / 25.4–38.1 × 1.65; 2 in 64.0 / 56.5 / 50.8 × 1.65; 2½ in 77.5 / 70.5 / 63.5 × 1.65; 3 in 91.0 / 83.5 / 76.2 × 1.65; 4 in 119.0 / 110.0 / 101.6 × 2.11; 6 in 166.9 (6.570 in) / 156.5 / 152.4 × 2.77; 8 in 217.7 (8.570 in) / 207.0 / 203.2 × 2.77; 10 in 268.5 / 261.0 / 254.0 × 3.40; 12 in 319.3 / 311.8 / 304.8 × 3.40.

Printable tri-clamp (45°): probe gland caps: Ø4, Ø6 and ¼ in probes… size chart

clampprobe (mm)portso ring
1–1½4.014 × 1.5
1–1½4.024 × 1.5
1–1½4.034 × 1.5
1–1½6.016 × 1.5
1–1½6.026 × 1.5
1–1½6.036 × 1.5
1–1½6.3516.35 × 1.5
1–1½6.3526.35 × 1.5
1–1½6.3536.35 × 1.5
24.014 × 1.5
24.024 × 1.5
24.034 × 1.5
26.016 × 1.5
26.026 × 1.5
26.036 × 1.5
26.3516.35 × 1.5
26.3526.35 × 1.5
26.3536.35 × 1.5

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
clamp faceISO 2852: 1–1½ in flange 50.5, groove 43.5; 2 in 64.0 / 56.5; 45° back conestandard Type B gasket and the 45° clamps (printable-tri-clamp-clamps): a 45° clamp fits only 45° rims, so keep a run all 45°clampgland-cap-*
probe boreØ4.0 / Ø6.0 / Ø6.35, 1 to 3 per capprobe: Ø4 thermocouple, 6 × 50 DS18B20, ¼ in RTDslidegland-cap-*
O-ring grooves2 internal grooves per bore for a probe Ø × 1.5 O-ring (4 × 1.5, 6 × 1.5, 6.35 × 1.5)O-rings seal the probe and let you set its depthdesignedgland-cap-*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

GW KentTri-clamp fittings guide: tube OD, flange OD and ID per size to 12 in; solid cap thicknesswebpublisher's guide; dimensions cited
Rubber FabTri-Clamp gasket dimensional chart: gasket ID, OD and bead diameter per size (2 in bead 2.22 in / 56.50 mm, 1.5 in 1.71 / 43.50, 3 in 3.29 / 83.50)PDFmaker chart; dimensions are facts verify

Free files

★ Free files 18 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
gland-cap-1.5in-4mm-x1-451–1½ in cap with 1 × Ø4 probe gland: Ø14 × 22 boss, two O-ring grooves Ø6.4 × 2 — printable, 45° rimsSTEP · STL
gland-cap-1.5in-4mm-x2-451–1½ in cap with 2 × Ø4 probe gland: Ø14 × 22 boss, two O-ring grooves Ø6.4 × 2 — printable, 45° rimsSTEP · STL
gland-cap-1.5in-4mm-x3-451–1½ in cap with 3 × Ø4 probe gland: Ø14 × 22 boss, two O-ring grooves Ø6.4 × 2 — printable, 45° rimsSTEP · STL
gland-cap-1.5in-6mm-x1-451–1½ in cap with 1 × Ø6 probe gland: Ø16 × 22 boss, two O-ring grooves Ø8.4 × 2 — printable, 45° rimsSTEP · STL
gland-cap-1.5in-6mm-x2-451–1½ in cap with 2 × Ø6 probe gland: Ø16 × 22 boss, two O-ring grooves Ø8.4 × 2 — printable, 45° rimsSTEP · STL
gland-cap-1.5in-6mm-x3-451–1½ in cap with 3 × Ø6 probe gland: Ø16 × 22 boss, two O-ring grooves Ø8.4 × 2 — printable, 45° rimsSTEP · STL
gland-cap-1.5in-6.35mm-x1-451–1½ in cap with 1 × Ø6.35 probe gland: Ø16.35 × 22 boss, two O-ring grooves Ø8.75 × 2 — printable, 45° rimsSTEP · STL
gland-cap-1.5in-6.35mm-x2-451–1½ in cap with 2 × Ø6.35 probe gland: Ø16.35 × 22 boss, two O-ring grooves Ø8.75 × 2 — printable, 45° rimsSTEP · STL
gland-cap-1.5in-6.35mm-x3-451–1½ in cap with 3 × Ø6.35 probe gland: Ø16.35 × 22 boss, two O-ring grooves Ø8.75 × 2 — printable, 45° rimsSTEP · STL
gland-cap-2in-4mm-x1-452 in cap with 1 × Ø4 probe gland: Ø14 × 22 boss, two O-ring grooves Ø6.4 × 2 — printable, 45° rimsSTEP · STL
gland-cap-2in-4mm-x2-452 in cap with 2 × Ø4 probe gland: Ø14 × 22 boss, two O-ring grooves Ø6.4 × 2 — printable, 45° rimsSTEP · STL
gland-cap-2in-4mm-x3-452 in cap with 3 × Ø4 probe gland: Ø14 × 22 boss, two O-ring grooves Ø6.4 × 2 — printable, 45° rimsSTEP · STL
gland-cap-2in-6mm-x1-452 in cap with 1 × Ø6 probe gland: Ø16 × 22 boss, two O-ring grooves Ø8.4 × 2 — printable, 45° rimsSTEP · STL
gland-cap-2in-6mm-x2-452 in cap with 2 × Ø6 probe gland: Ø16 × 22 boss, two O-ring grooves Ø8.4 × 2 — printable, 45° rimsSTEP · STL
gland-cap-2in-6mm-x3-452 in cap with 3 × Ø6 probe gland: Ø16 × 22 boss, two O-ring grooves Ø8.4 × 2 — printable, 45° rimsSTEP · STL
gland-cap-2in-6.35mm-x1-452 in cap with 1 × Ø6.35 probe gland: Ø16.35 × 22 boss, two O-ring grooves Ø8.75 × 2 — printable, 45° rimsSTEP · STL
gland-cap-2in-6.35mm-x2-452 in cap with 2 × Ø6.35 probe gland: Ø16.35 × 22 boss, two O-ring grooves Ø8.75 × 2 — printable, 45° rimsSTEP · STL
gland-cap-2in-6.35mm-x3-452 in cap with 3 × Ø6.35 probe gland: Ø16.35 × 22 boss, two O-ring grooves Ø8.75 × 2 — printable, 45° rimsSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=printable-tri-clamp-probe-gland-caps

Printable tri-clamp (45°): probe gland caps: Ø4, Ø6 and ¼ in probes, 1 to 3 per cap, isometric render of a generated part
Render of gland-cap-2in-4mm-x1-45 from the free STEP; not to scale.

Fits with

Questions

Can I 3D print this?

Yes. It is the 3D-printable version: every overhang is 45° or steeper, so it prints without supports, and the sealing face is standard ISO 2852, so a normal gasket and clamp fit.

Which O-ring?

One the size of the probe with a 1.5 mm section (6 × 1.5 for a 6 mm probe), two per port.