Library › Tri-clamp & pipe › Clamp fittings ·

Two-bolt clamps for 6 and 8 in tri-clamp joints

What clamp fits a 6 inch tri-clamp? · Hardware · basis: Groove is the ISO 2852 rim's 20° back cone mirrored (as the 10 and 12 in clamps on this site): contact after 0.4 mm of travel per half, 0.6 mm more squeezes the gasket before the halves meet

Also called: 6 inch tri clamp clamp, 8 inch tri clamp clamp, printable tri clamp 6

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
2 in table

Notes

  • Two identical halves per joint, turned 180° to each other; tighten the two M8 bolts evenly until the halves just meet.
  • Every clamp face is the ISO 2852 profile used across this site: 2.85 mm rim, flat face with the gasket groove (K 1.6 deep, R3 1.2 bottom, 23° walls, P2 0.8 edges) on C2, 20° back cone. Flange C3 / groove C2 / tube OD × wall, mm: ½–¾ in 25.0 / 20.4 (derived) / 12.7–19.05 × 1.65; 1–1½ in 50.5 / 43.5 / 25.4–38.1 × 1.65; 2 in 64.0 / 56.5 / 50.8 × 1.65; 2½ in 77.5 / 70.5 / 63.5 × 1.65; 3 in 91.0 / 83.5 / 76.2 × 1.65; 4 in 119.0 / 110.0 / 101.6 × 2.11; 6 in 166.9 (6.570 in) / 156.5 / 152.4 × 2.77; 8 in 217.7 (8.570 in) / 207.0 / 203.2 × 2.77; 10 in 268.5 / 261.0 / 254.0 × 3.40; 12 in 319.3 / 311.8 / 304.8 × 3.40.

Two-bolt clamps for 6 and 8 in tri-clamp joints size chart

size (in)clamp od (mm)width (mm)bolts
6180.919.432 × M8 × 40 + nuts
8231.719.432 × M8 × 40 + nuts

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
clamp pairtwo identical halves turned 180°, M8 boltscloses on flange C3 Ø166.9 (6 in) / Ø217.7 (8 in), rear cone 20°; tighten evenly until the halves meetclampclamp-half-*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

GW KentTri-clamp fittings guide: tube OD, flange OD and ID per size to 12 in; solid cap thicknesswebpublisher's guide; dimensions cited
Rubber FabTri-clamp dimensions chart (ID, OD, bead per clamp size, ½ to 12 in and DIN 32676)PDFpublisher's chart; dimensions cited, nothing copied
Rubber FabTri-Clamp gasket dimensional chart: gasket ID, OD and bead diameter per size (2 in bead 2.22 in / 56.50 mm, 1.5 in 1.71 / 43.50, 3 in 3.29 / 83.50)PDFmaker chart; dimensions are facts verify

Free files

★ Free files 2 parts. Generated by Xem Studio from the standard; threads are plain cylinders at major diameter. CC BY 4.0. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
clamp-half-6in-m86 in two-bolt clamp half (two per joint): 20° groove, contact after 0.4, 0.6 squeeze; Ø180.9 × 19.43 wide; M8 × 40 hex bolts (ISO 4017), head in a 13 AF pocket on one lugSTEP · STL
clamp-half-8in-m88 in two-bolt clamp half (two per joint): 20° groove, contact after 0.4, 0.6 squeeze; Ø231.7 × 19.43 wide; M8 × 40 hex bolts (ISO 4017), head in a 13 AF pocket on one lugSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=sanitary-clamp-clamps-6-8in

Two-bolt clamps for 6 and 8 in tri-clamp joints, isometric render of a generated part
Render of clamp-half-8in-m8 from the free STEP; not to scale.

Fits with

Questions

How does the clamp seat?

The 20° groove wedges the two rims together; when the halves meet, the gasket is squeezed by design.