Library › Tri-clamp & pipe › Clamp fittings ·

Two-bolt clamps for DIN 32676 flanges 34, 106, 155 and 183 mm

What clamp fits a 34 mm DIN 32676 flange? · Hardware · basis: Groove = the ISO 2852 rim's 20° back cone mirrored, as tri-clamp-clamps on this site; 50.5, 64, 91 and 119 mm flanges use those inch clamps

Also called: 34mm tri clamp clamp, din clamp 106

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
4 in table

Notes

  • Only the metric-only flange sizes are here; the shared sizes are on the tri-clamp clamps page.
  • Every clamp face is the ISO 2852 profile used across this site: 2.85 mm rim, flat face with the gasket groove (K 1.6 deep, R3 1.2 bottom, 23° walls, P2 0.8 edges) on C2, 20° back cone. Flange C3 / groove C2 / tube OD × wall, mm: ½–¾ in 25.0 / 20.4 (derived) / 12.7–19.05 × 1.65; 1–1½ in 50.5 / 43.5 / 25.4–38.1 × 1.65; 2 in 64.0 / 56.5 / 50.8 × 1.65; 2½ in 77.5 / 70.5 / 63.5 × 1.65; 3 in 91.0 / 83.5 / 76.2 × 1.65; 4 in 119.0 / 110.0 / 101.6 × 2.11; 6 in 166.9 (6.570 in) / 156.5 / 152.4 × 2.77; 8 in 217.7 (8.570 in) / 207.0 / 203.2 × 2.77; 10 in 268.5 / 261.0 / 254.0 × 3.40; 12 in 319.3 / 311.8 / 304.8 × 3.40.

Two-bolt clamps for DIN 32676 flanges 34, 106, 155 and 183 mm size chart

flange (mm)clamp od (mm)width (mm)
34.043.018.8
106.0115.018.8
155.0164.020.6
183.0192.021.7

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
clamp halvesmetric-only flanges 34 / 106 / 155 / 183flange of the same Ø; shared sizes (50.5, 64, 91, 119) use the tri-clamp clampsclampclamp-half-*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

DINDIN 32676 clamp connections, series A on DIN 11850 tube (DN10–DN150): flange and bead per the Rubber Fab chartstandardDIN; dimensions are facts verify
Rubber FabTri-clamp dimensions chart (ID, OD, bead per clamp size, ½ to 12 in and DIN 32676)PDFpublisher's chart; dimensions cited, nothing copied
Rubber FabTri-Clamp gasket dimensional chart: gasket ID, OD and bead diameter per size (2 in bead 2.22 in / 56.50 mm, 1.5 in 1.71 / 43.50, 3 in 3.29 / 83.50)PDFmaker chart; dimensions are facts verify

Free files

★ Free files 4 parts. Generated by Xem Studio from the standard; threads are plain cylinders at major diameter. CC BY 4.0. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
clamp-half-34mmtwo-bolt clamp half for the 34 mm flange (two per joint): 20° groove, contact after 0.4, 0.6 squeeze, M5 × 30 boltsSTEP · STL
clamp-half-106mmtwo-bolt clamp half for the 106 mm flange (two per joint): 20° groove, contact after 0.4, 0.6 squeeze, M5 × 30 boltsSTEP · STL
clamp-half-155mmtwo-bolt clamp half for the 155 mm flange (two per joint): 20° groove, contact after 0.4, 0.6 squeeze, M5 × 30 boltsSTEP · STL
clamp-half-183mmtwo-bolt clamp half for the 183 mm flange (two per joint): 20° groove, contact after 0.4, 0.6 squeeze, M5 × 30 boltsSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=sanitary-clamp-din-32676-clamps

Two-bolt clamps for DIN 32676 flanges 34, 106, 155 and 183 mm, isometric render of a generated part
Render of clamp-half-155mm from the free STEP; not to scale.

Fits with

Questions

Which clamp for DN50?

DN50 has the 64 mm flange: use the 2 in tri-clamp clamp.