Library › Tri-clamp & pipe › Clamp fittings ·
Tri-clamp dome lids: 1½ to 12 in, plain or with a port at the crown
Is there a domed tri-clamp lid with a port on top? · Hardware · basis: Xem Studio design: an F&D head (crown radius = OD, knuckle 6 %) on a short skirt of the size's tube, with the ISO 2852 face; ports are a ½ NPT Class 3000 half coupling or a 1½ in clamp nozzle
Also called: tri clamp dome lid, domed end cap tri clamp, 6 inch tri clamp lid, tri clamp dome with port, fermenter dome lid tri clamp
Exact dimensions. True size, with no tolerance added.
- sizes
- 8 in table
Notes
- Domed lids for the same size of ferrule, vessel or spool. The dome sheds condensate back into the vessel and leaves headspace; the crown port takes an airlock, a blow-off, a thermowell or a spunding valve through a 1½ in clamp or ½ NPT.
- Every clamp face is the ISO 2852 profile used across this site: 2.85 mm rim, flat face with the gasket groove (K 1.6 deep, R3 1.2 bottom, 23° walls, P2 0.8 edges) on C2, 20° back cone. Flange C3 / groove C2 / tube OD × wall, mm: ½–¾ in 25.0 / 20.4 (derived) / 12.7–19.05 × 1.65; 1–1½ in 50.5 / 43.5 / 25.4–38.1 × 1.65; 2 in 64.0 / 56.5 / 50.8 × 1.65; 2½ in 77.5 / 70.5 / 63.5 × 1.65; 3 in 91.0 / 83.5 / 76.2 × 1.65; 4 in 119.0 / 110.0 / 101.6 × 2.11; 6 in 166.9 (6.570 in) / 156.5 / 152.4 × 2.77; 8 in 217.7 (8.570 in) / 207.0 / 203.2 × 2.77; 10 in 268.5 / 261.0 / 254.0 × 3.40; 12 in 319.3 / 311.8 / 304.8 × 3.40.
Tri-clamp dome lids: 1½ to 12 in, plain or with a port at the crown size chart
| size (in) | tube od (mm) | dome height (mm) |
|---|---|---|
| 1½ | 38.1 | 6.5 |
| 2 | 50.8 | 8.6 |
| 3 | 76.2 | 12.9 |
| 4 | 101.6 | 17.2 |
| 6 | 152.4 | 25.8 |
| 8 | 203.2 | 34.4 |
| 10 | 254.0 | 43.0 |
| 12 | 304.8 | 51.6 |
Where the files are
Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.
| ASME | Flanged and dished (F&D) heads: crown radius = OD, knuckle radius 6 % of OD (BPVC Section VIII torispherical head) | standard | ASME; proportions are facts verify |
| ASME | B1.20.1 Pipe threads, general purpose (NPT): major diameter, L2, tap drill; B16.11 forged fittings (Class 3000 couplings); B36.10 Sch 40 bore | standard | ASME; dimensions are facts verify |
| GW Kent | Tri-clamp fittings guide: tube OD, flange OD and ID per size to 12 in; solid cap thickness | web | publisher's guide; dimensions cited |
| Rubber Fab | Tri-Clamp gasket dimensional chart: gasket ID, OD and bead diameter per size (2 in bead 2.22 in / 56.50 mm, 1.5 in 1.71 / 43.50, 3 in 3.29 / 83.50) | maker chart; dimensions are facts verify |
Free files
★ Free files 16 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json
Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.
Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp- Claude: Add to Claude
- ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
- Cursor: install with one click. VS Code: install with one click.
| dome-lid-1.5in | 1½ in dome lid (F&D head), 14.6 from the face to the crown | STEP · STL |
| dome-lid-2in | 2 in dome lid (F&D head), 16.9 from the face to the crown | STEP · STL |
| dome-lid-2in-half-npt | 2 in dome lid with a ½ NPT half coupling at the crown (tap-drill bore Ø18.3) | STEP · STL |
| dome-lid-3in | 3 in dome lid (F&D head), 21.4 from the face to the crown | STEP · STL |
| dome-lid-3in-half-npt | 3 in dome lid with a ½ NPT half coupling at the crown (tap-drill bore Ø18.3) | STEP · STL |
| dome-lid-4in | 4 in dome lid (F&D head), 26.2 from the face to the crown | STEP · STL |
| dome-lid-4in-half-npt | 4 in dome lid with a ½ NPT half coupling at the crown (tap-drill bore Ø18.3) | STEP · STL |
| dome-lid-4in-1.5in-port | 4 in dome lid with a 1½ in clamp port at the crown, 51.6 from the face to the port face | STEP · STL |
| dome-lid-6in | 6 in dome lid (F&D head), 34.3 from the face to the crown | STEP · STL |
| dome-lid-6in-1.5in-port | 6 in dome lid with a 1½ in clamp port at the crown, 59.7 from the face to the port face | STEP · STL |
| dome-lid-8in | 8 in dome lid (F&D head), 42.9 from the face to the crown | STEP · STL |
| dome-lid-8in-1.5in-port | 8 in dome lid with a 1½ in clamp port at the crown, 68.3 from the face to the port face | STEP · STL |
| dome-lid-10in | 10 in dome lid (F&D head), 51.5 from the face to the crown | STEP · STL |
| dome-lid-10in-1.5in-port | 10 in dome lid with a 1½ in clamp port at the crown, 76.9 from the face to the port face | STEP · STL |
| dome-lid-12in | 12 in dome lid (F&D head), 60.1 from the face to the crown | STEP · STL |
| dome-lid-12in-1.5in-port | 12 in dome lid with a 1½ in clamp port at the crown, 85.5 from the face to the port face | STEP · STL |
https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.Plain text: sheet.txt · JSON: /api/geometry?object=tri-clamp-dome-lids

Fits with



Questions
What goes in the crown port?
Anything with a 1½ in clamp (airlock cap, thermowell, blow-off) or a ½ NPT fitting.