Library › Hardware › Heat transfer ·

Tri-clamp jacket shell: clamp-on sealed jacket for a 2 in tube

Can I put a liquid or thermal-storage jacket on a tri-clamp tube? · Hardware · basis: ASME BPE 2 in tube OD (Ø50.8); chamber volume from the drawn geometry

Also called: tri clamp cooling jacket, water jacket stirling, clamp on jacket 2 inch tube, stirling cold side jacket

Long Earth Society build part. An alternative to the fins on my elbow alpha's cold leg. Long Earth Society

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
2 in table

Notes

  • A separate, optional heat exchanger: the tube it clamps on stays a plain standard part, and an engine is complete without it.
  • Two halves close on the tube OD in the same place as the finned cooler. Each half is a sealed half-annular chamber: inner wall 2 mm on the tube, chamber 10 mm, outer wall 2 mm, closed ends and a closed split wall, so each half holds its own fill (50.3 mL).
  • Each half has one fill port at its top: a Ø6 port through a Ø12 × 4 boss on the outer wall, 8 mm below the top end, closed by the cap (Ø6 spigot). Fill it with the jacket standing as on the engine, port up. The fill is the builder's choice.
  • The same four M4 × 30 screws and nuts as the cooler hold the halves on the tube.

Tri-clamp jacket shell: clamp-on sealed jacket for a 2 in tube size chart

partbore (mm)length (mm)chamber ml per halfport (mm)
jacket half50.856.050.36.0
port cap7.06.0

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
boreØ50.82 in tube ODclampjacket-half-*
ear holesØ4.5M4 clearance (ISO 273 medium)designedjacket-half-*
fill portØ6fill-port cap spigotpressjacket-half-*
cap spigotØ6 × 4fill portpressjacket-port-cap*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

ISO (via iTeh sample)ISO 2852 clamp liners: face profile and flange / groove diametersPDFstandard excerpt; dimensions are facts
ASMEBPE Bioprocessing Equipment (clamp fitting dimensions, tube OD and wall)standardASME; dimensions are facts verify
Long Earth SocietyEngine buildsweb, videoLES site

Free files

★ Free files 2 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
jacket-half-2in-56clamp-on jacket half for the 2 in tube OD (Ø50.8 bore) × 56: inner wall 2 on the tube, closed chamber 10 wide (50.3 mL per half), outer wall 2, end walls 2, Ø6 fill port in a Ø12 × 4 boss on the outer wall 8 below the top end; ears as the finned coolerSTEP · STL
jacket-port-capfill-port cap: Ø12 × 3 with a Ø6 × 4 spigotSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=tri-clamp-jacket-shell

Tri-clamp jacket shell: clamp-on sealed jacket for a 2 in tube, isometric render of a generated part
Render of jacket-port-cap from the free STEP; not to scale.

Fits with

Questions

How much does the jacket hold?

50.3 mL per half, 100.7 mL in all.

Can I use it with the fins?

Not on the same 3 in spool: both take the whole plain length. It replaces the finned cooler.