Library › Tri-clamp & pipe › Inserts & liners ·

Slotted fin inserts for a 2 in tri-clamp bore (heater and cooler sleeves)

What fin insert adds heat-transfer area inside a 2 inch tri-clamp bore? · Hardware · basis: Design values of the free-piston generator: 36 axial slots 1.5 × 2.5 in a sleeve whose OD is the 2 in bore (Ø47.5); heat-transfer and flow numbers from the generator's simple analysis

Also called: stirling heater insert, internal fins stirling cooler, slotted heat exchanger sleeve

Long Earth Society build part. Optional fin inserts for my free-piston generator. Long Earth Society

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
2 in table

Notes

  • Two slotted sleeves that slide into the plain tri-clamp parts: the heater insert on the liner's lower end inside the closed-end spool, the cooler insert pressed into the 3 in spool under the water jacket. The gas runs along the 36 slots, between fins that touch the wall.
  • Optional: without them the heater is the plain 3.0 mm annulus round the liner and the cooler the 4.05 mm annulus round the displacer. The engine still runs; my analysis gives 6.6 W instead of 43.2 W at the same stroke (helium, 10 bar), because the gas-side heat transfer falls and the cooler annulus adds dead volume.
  • Fits: the heater insert slides on the liner (press) and its OD against the hot spool's bore (slide); the cooler insert's OD is pressed into S3, its Ø40 bore is the displacer's 0.30 gap.

Slotted fin inserts for a 2 in tri-clamp bore size chart

insertid (mm)od (mm)length (mm)slotsslot (mm)
heater41.547.568.05361.5 × 2.5
cooler40.047.573.2361.5 × 2.5

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
boreØ41.5liner tube ODpressfpse-heater-insert*
ODØ47.5hot spool bore (hot wall)slidefpse-heater-insert*
ODØ47.5S3 spool borepressfpse-cooler-insert*
boreØ40.00displacer Ø39.4 (0.30 radial gap, no contact)designedfpse-cooler-insert*
slots36 × 1.5 wide × 2.5 deepgas passages (no contact)designedall

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

Ohio University (Urieli)Stirling cycle machine analysis: ideal adiabatic and simple analysis (after Urieli & Berchowitz, Stirling Cycle Engine Analysis, 1984)webauthor's site
Long Earth SocietyEngine buildsweb, videoLES site

Free files

★ Free files 2 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
fpse-heater-insert-41.5x47.5heater insert (optional): Ø41.5 / Ø47.5 × 68.05, 36 slots 1.5 × 2.5 deep in the OD, full length; on the liner's lower end, OD against the hot wallSTEP · STL
fpse-cooler-insert-40x47.5cooler insert (optional): Ø40 / Ø47.5 × 73.2, 36 slots 1.5 × 2.5 deep in the OD; pressed into the 3 in spool S3, its bore continues the displacer's boreSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=tri-clamp-slotted-fin-inserts

Slotted fin inserts for a 2 in tri-clamp bore (heater and cooler sleeves), isometric render of a generated part
Render of fpse-cooler-insert-40x47.5 from the free STEP; not to scale.

Fits with

Questions

What if I leave them out?

The engine is complete without them; expect about 6.6 W instead of 43.2 W at 10 bar helium.