Library › Electronic components › Generators & alternators ·

Linear alternator stator outside a 2 in tube: laminated two-tooth stator, one coil

What linear alternator stator fits outside a 2 inch tube? · Hardware · basis: Two-tooth moving-magnet topology (flux through the coil reverses as the magnet rows pass under the teeth); magnetic-circuit estimate with the magnets' published remanence; coil numbers from the winding window

Also called: linear alternator outside tube, hermetic linear alternator stirling, moving magnet linear generator stator

Long Earth Society build part. The alternator of my free-piston generator. Long Earth Society

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
6 in table

Notes

  • The coil and its iron never touch the gas: they sit round the bored spool's 1.40 wall, which is not magnetic for this to work. Eight packs of radial laminations form two teeth on the tube and a yoke outside the coil; the flux from the S N N S magnet rows closes through one tooth, the yoke and the other, and reverses through the coil as the piston moves ±6 (the linear range: half a tooth).
  • Estimate: gap flux density 0.42 T (magnets 1.31 T, 63 % of the carrier covered, 1.9 mm magnetic gap), 75 % of it linking the coil; dΦ/dx 0.096 Wb/m; with 300 turns of 0.71 mm wire: force constant 28.8 N/A (V·s/m), coil 3.40 Ω, inductance about 25 mH.
  • At the design point (10 bar helium, ±5.0 mm, 45.1 Hz) it gives 40.8 V peak open circuit and 43.2 W into 11.5 Ω through a 500 µF series capacitor that cancels the coil's inductance (20 V peak across it). The load is the stroke control: never run it open-circuit.
  • The flux in the laminations reverses at the running frequency: the plates must be thin and insulated from each other (drawn as 0.5 mm, as the pack envelope). The coil slides over S4's flange before the stack is clamped; the housing halves clamp the packs onto the tube with 4 × M4 × 20; the leads leave through the housing's hole between two packs.

Linear alternator stator outside a 2 in tube: laminated two-tooth… size chart

itemvalue
teeth2 × 12 wide, slot 16
packs8 × 43°, r 25.4–55
coil300 t, 0.71 mm, 3.40 Ω
force constant28.8 N/A
inductance (est.)25 mH
linear range±6 mm

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
teethr 25.4 (Ø50.8)S4 tube ODclampfpse-stator-pack*
ODØ110housing boreclampfpse-stator-pack*
bobbin boreØ65slips over S4's Ø64 flange (no contact)designedfpse-bobbin*
ear holes2 × Ø4.5 each sideM4 × 20 and nuts (ISO 273 medium)designedfpse-stator-housing*
split1.0 total (0.5 per half)the other halfclampfpse-stator-housing*
lead holeØ6coil leadsdesignedfpse-stator-housing*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

K&J MagneticsNeodymium magnet specifications: N42 Br 1.30–1.32 T, density 7.4–7.5 g/cm³webmaker page; values are facts verify
Long Earth SocietyEngine buildsweb, videoLES site

Free files

★ Free files 4 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
fpse-stator-pack-43degstator pack: 43° of radial laminations 0.5 thick, two teeth r 25.4–50 at |z| 8–20, yoke r 50–55; drawn as its envelope; 8 round the tubeSTEP · STL
fpse-bobbin-65bobbin Ø65 / Ø67 × 16, flanges Ø99 × 1: slips over S4's Ø64 flangesSTEP · STL
fpse-coil-300tcoil: 300 turns of 0.71 mm enamelled wire, the winding volume Ø67–Ø99 × 14STEP · STL
fpse-stator-housing-halfstator housing half: shell r 55–58, end walls to r 34, ears with 2 × M4 each side, Ø6 lead hole; two halves clamp the packs onto the tubeSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=linear-alternator-stator-2in-tube

Linear alternator stator outside a 2 in tube: laminated two-tooth stator, one coil, isometric render of a generated part
Render of fpse-coil-300t from the free STEP; not to scale.

Fits with

Questions

Why outside the wall?

No wire through the pressure boundary and no coil in the gas: the vessel stays a sealed stack of tri-clamp parts. The price is 1.4 mm more magnetic gap than an inside coil.

What sets the stroke?

The load. The alternator's damping absorbs the engine's power; less load (higher resistance) lets the stroke grow. Keep a load connected whenever the engine is hot.