Library › Tri-clamp & pipe › Clamp fittings ·
Sanitary clamp reducers, concentric and eccentric, ½ to 4 in (tri-clamp style, BPE)
How long is a 2 × 1½ inch sanitary clamp reducer? · Standard part · basis: ASME BPE / 3-A clamp-fitting dimensions published identically by two manufacturers; ISO 2852 face profile; drawn by Xem Studio from those numbers
Also called: tri clamp reducer dimensions, sanitary reducer 2 x 1.5, eccentric tri clamp reducer, concentric reducer tri clamp, tri clamp reducer stl
Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features
- sizes
- 13 in table
Notes
- Concentric (31-14MP) and eccentric (32-14MP) reducers with clamp faces both ends; 0.5 in of straight tube behind each face, then the cone. Eccentric reducers keep one side flat (drawn on −X): lay it flat side down so a line drains.
- Only the size pairs and lengths that both source catalogues list identically are drawn.
- ISO 2852 face: flat from the bore to the flange OD, gasket groove on C2 1.6 deep, bottom radius 1.2, walls 23°, edge radius 0.8; 2.85 mm rim, 20° back cone, on the BPE flange diameters ½–¾ in 25.0, 1–1½ in 50.5, 2 in 64.0, 2½ in 77.5, 3 in 91.0, 4 in 119.0 mm; tube OD 12.7 / 19.05 / 25.4 / 38.1 / 50.8 / 63.5 / 76.2 / 101.6 mm, wall 1.65 mm (4 in: 2.11). The gasket-groove diameter on ½ and ¾ in is derived (Ø20.4, centred between the ¾ in bore and the 25.0 flange so the groove fits); 4 in is Ø110.0 from the published gasket chart; the rest is from the standard. Type B gaskets: 1.7 web out to flange − 1, a bulge on each side on the groove diameter (5.5 overall), lip 1.1 inside the bore and 2.8 long; with the faces 1.7 apart each bulge is squeezed 0.3 into its groove (designed).
Sanitary clamp reducers, concentric and eccentric, ½ to 4 in size chart
| size (in) | face to face (mm) | large tube od (mm) | small tube od (mm) |
|---|---|---|---|
| ¾ × ½ | 50.8 | 19.05 | 12.7 |
| 1 × ¾ | 50.8 | 25.4 | 19.05 |
| 1½ × 1 | 76.2 | 38.1 | 25.4 |
| 2 × 1 | 127.0 | 50.8 | 25.4 |
| 2 × 1½ | 76.2 | 50.8 | 38.1 |
| 2½ × 1½ | 127.0 | 63.5 | 38.1 |
| 2½ × 2 | 76.2 | 63.5 | 50.8 |
| 3 × 1½ | 177.8 | 76.2 | 38.1 |
| 3 × 2 | 127.0 | 76.2 | 50.8 |
| 3 × 2½ | 76.2 | 76.2 | 63.5 |
| 4 × 2 | 231.8 | 101.6 | 50.8 |
| 4 × 2½ | 181.0 | 101.6 | 63.5 |
| 4 × 3 | 130.2 | 101.6 | 76.2 |
Mating features
Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.
| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| clamp faces | ISO 2852 / BPE flange | clamp + Type B gasket, large and small size | clamp | all |
Where the files are
Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.
| ASME | BPE Bioprocessing Equipment (clamp fitting dimensions, tube OD and wall) | standard | ASME; dimensions are facts verify |
| ISO (via iTeh sample) | ISO 2852 clamp liners: face profile and flange / groove diameters | standard excerpt; dimensions are facts | |
| Dixon Sanitary | Clamp elbows, ferrules: dimension sheet | publisher's catalogue; dimensions cited, nothing copied | |
| Steel & O'Brien | Sanitary products catalog 2024 (clamp fittings dimension tables) | publisher's catalogue; dimensions cited, nothing copied | |
| Rubber Fab | Tri-Clamp gasket dimensional chart: gasket ID, OD and bead diameter per size (2 in bead 2.22 in / 56.50 mm, 1.5 in 1.71 / 43.50, 3 in 3.29 / 83.50) | maker chart; dimensions are facts verify |
Free files
★ Free files 26 parts. Generated by Xem Studio from the standard; threads are plain cylinders at major diameter. CC BY 4.0. index.json
Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.
Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp- Claude: Add to Claude
- ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
- Cursor: install with one click. VS Code: install with one click.
| reducer-concentric-0.75inx0.5in | ¾ × ½ in concentric reducer (31-14MP), 2.0 in face to face | STEP · STL |
| reducer-eccentric-0.75inx0.5in | ¾ × ½ in eccentric reducer (32-14MP), 2.0 in face to face, flat side on −X | STEP · STL |
| reducer-concentric-1inx0.75in | 1 × ¾ in concentric reducer (31-14MP), 2.0 in face to face | STEP · STL |
| reducer-eccentric-1inx0.75in | 1 × ¾ in eccentric reducer (32-14MP), 2.0 in face to face, flat side on −X | STEP · STL |
| reducer-concentric-1.5inx1in | 1½ × 1 in concentric reducer (31-14MP), 3.0 in face to face | STEP · STL |
| reducer-eccentric-1.5inx1in | 1½ × 1 in eccentric reducer (32-14MP), 3.0 in face to face, flat side on −X | STEP · STL |
| reducer-concentric-2inx1in | 2 × 1 in concentric reducer (31-14MP), 5.0 in face to face | STEP · STL |
| reducer-eccentric-2inx1in | 2 × 1 in eccentric reducer (32-14MP), 5.0 in face to face, flat side on −X | STEP · STL |
| reducer-concentric-2inx1.5in | 2 × 1½ in concentric reducer (31-14MP), 3.0 in face to face | STEP · STL |
| reducer-eccentric-2inx1.5in | 2 × 1½ in eccentric reducer (32-14MP), 3.0 in face to face, flat side on −X | STEP · STL |
| reducer-concentric-2.5inx1.5in | 2½ × 1½ in concentric reducer (31-14MP), 5.0 in face to face | STEP · STL |
| reducer-eccentric-2.5inx1.5in | 2½ × 1½ in eccentric reducer (32-14MP), 5.0 in face to face, flat side on −X | STEP · STL |
| reducer-concentric-2.5inx2in | 2½ × 2 in concentric reducer (31-14MP), 3.0 in face to face | STEP · STL |
| reducer-eccentric-2.5inx2in | 2½ × 2 in eccentric reducer (32-14MP), 3.0 in face to face, flat side on −X | STEP · STL |
| reducer-concentric-3inx1.5in | 3 × 1½ in concentric reducer (31-14MP), 7.0 in face to face | STEP · STL |
| reducer-eccentric-3inx1.5in | 3 × 1½ in eccentric reducer (32-14MP), 7.0 in face to face, flat side on −X | STEP · STL |
| reducer-concentric-3inx2in | 3 × 2 in concentric reducer (31-14MP), 5.0 in face to face | STEP · STL |
| reducer-eccentric-3inx2in | 3 × 2 in eccentric reducer (32-14MP), 5.0 in face to face, flat side on −X | STEP · STL |
| reducer-concentric-3inx2.5in | 3 × 2½ in concentric reducer (31-14MP), 3.0 in face to face | STEP · STL |
| reducer-eccentric-3inx2.5in | 3 × 2½ in eccentric reducer (32-14MP), 3.0 in face to face, flat side on −X | STEP · STL |
| reducer-concentric-4inx2in | 4 × 2 in concentric reducer (31-14MP), 9.125 in face to face | STEP · STL |
| reducer-eccentric-4inx2in | 4 × 2 in eccentric reducer (32-14MP), 9.125 in face to face, flat side on −X | STEP · STL |
| reducer-concentric-4inx2.5in | 4 × 2½ in concentric reducer (31-14MP), 7.125 in face to face | STEP · STL |
| reducer-eccentric-4inx2.5in | 4 × 2½ in eccentric reducer (32-14MP), 7.125 in face to face, flat side on −X | STEP · STL |
| reducer-concentric-4inx3in | 4 × 3 in concentric reducer (31-14MP), 5.125 in face to face | STEP · STL |
| reducer-eccentric-4inx3in | 4 × 3 in eccentric reducer (32-14MP), 5.125 in face to face, flat side on −X | STEP · STL |
https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.Plain text: sheet.txt · JSON: /api/geometry?object=sanitary-clamp-reducers

How it fits
Connects to
Alternatives
You might also need
Questions
How long is a 2 × 1½ in sanitary clamp reducer?
3.0 in (76.2 mm) face to face, concentric or eccentric.
Concentric or eccentric?
Concentric keeps the centreline; eccentric keeps one side flat so a horizontal line drains or vents without a pocket.
