Library › Tri-clamp & pipe › Clamp fittings ·

Sanitary clamp tees and short-outlet tees (7MP, 7MPS): ½ to 4 in

What are the dimensions of a 2 inch tri-clamp tee? · Standard part · basis: ASME BPE / 3-A clamp-fitting dimensions published identically by Dixon and Steel & O'Brien; ISO 2852 face profile

Also called: tri clamp tee dimensions, sanitary tee 2 inch, 7mp tee, short outlet tee, tri clamp tee stl

Used in Long Earth Society builds. S-type layout: does cold need to sit above hot?

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
8 in table

Notes

  • Equal tee (7MP): a run with a face at each end and one branch of the same size at 90°. Run face to face B, branch centre to face A.
  • Short-outlet tee (7MPS): the same run with a branch only as long as its flange needs, for a gauge, probe or valve right at the line; 1 to 4 in.
  • Faces are the ISO 2852 profile: flat from the bore out to the flange OD with one gasket groove centred on the groove diameter (1.6 deep, bottom radius 1.2, walls 23°, edge radius 0.8, 4.01 wide at the face), 2.85 mm rim, 20° back cone, on the BPE flange diameters; the groove diameter is ISO 2852's C2 and the bead diameter of published gasket charts (4 in Ø110.0 from the chart); on ½ and ¾ in it is derived (Ø20.4, centred between the ¾ in bore and the flange OD).

Sanitary clamp tees and short-outlet tees (7MP, 7MPS): ½ to 4 in size chart

size (in)run face to face (mm)branch centre to face (mm)short branch centre to face (mm)
½63.531.8—
¾120.660.3—
1120.660.328.6
1½139.769.834.9
2177.888.941.3
2½177.888.947.6
3190.595.254.0
4228.6114.369.8

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
clamp facesISO 2852 / BPE flangeclamp + Type B gasket to any fitting of the same sizeclampall

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

ASMEBPE Bioprocessing Equipment (clamp fitting dimensions, tube OD and wall)standardASME; dimensions are facts verify
ISO (via iTeh sample)ISO 2852 clamp liners: face profile and flange / groove diametersPDFstandard excerpt; dimensions are facts
Dixon SanitaryClamp elbows, ferrules: dimension sheetPDFpublisher's catalogue; dimensions cited, nothing copied
Steel & O'BrienSanitary products catalog 2024 (clamp fittings dimension tables)PDFpublisher's catalogue; dimensions cited, nothing copied
Rubber FabTri-Clamp gasket dimensional chart: gasket ID, OD and bead diameter per size (2 in bead 2.22 in / 56.50 mm, 1.5 in 1.71 / 43.50, 3 in 3.29 / 83.50)PDFmaker chart; dimensions are facts verify

Free files

★ Free files 14 parts. Generated by Xem Studio from the standard; threads are plain cylinders at major diameter. CC BY 4.0. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
tee-0.5in½ in equal tee (7MP): run 2.5 in face to face, branch 1.25 in centre to faceSTEP · STL
tee-0.75in¾ in equal tee (7MP): run 4.75 in face to face, branch 2.375 in centre to faceSTEP · STL
tee-1in1 in equal tee (7MP): run 4.75 in face to face, branch 2.375 in centre to faceSTEP · STL
tee-short-1in1 in short-outlet tee (7MPS): run 4.75 in, branch 1.125 in centre to faceSTEP · STL
tee-1.5in1½ in equal tee (7MP): run 5.5 in face to face, branch 2.75 in centre to faceSTEP · STL
tee-short-1.5in1½ in short-outlet tee (7MPS): run 5.5 in, branch 1.375 in centre to faceSTEP · STL
tee-2in2 in equal tee (7MP): run 7.0 in face to face, branch 3.5 in centre to faceSTEP · STL
tee-short-2in2 in short-outlet tee (7MPS): run 7.0 in, branch 1.625 in centre to faceSTEP · STL
tee-2.5in2½ in equal tee (7MP): run 7.0 in face to face, branch 3.5 in centre to faceSTEP · STL
tee-short-2.5in2½ in short-outlet tee (7MPS): run 7.0 in, branch 1.875 in centre to faceSTEP · STL
tee-3in3 in equal tee (7MP): run 7.5 in face to face, branch 3.75 in centre to faceSTEP · STL
tee-short-3in3 in short-outlet tee (7MPS): run 7.5 in, branch 2.125 in centre to faceSTEP · STL
tee-4in4 in equal tee (7MP): run 9.0 in face to face, branch 4.5 in centre to faceSTEP · STL
tee-short-4in4 in short-outlet tee (7MPS): run 9.0 in, branch 2.75 in centre to faceSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=sanitary-clamp-tees

Sanitary clamp tees and short-outlet tees (7MP, 7MPS): ½ to 4 in, isometric render of a generated part
Render of tee-2in from the free STEP; not to scale.

You might also need

Questions

How long is a 2 inch sanitary clamp tee?

177.8 mm (7.0 in) face to face on the run, 88.9 mm (3.5 in) centre to branch face.

What is a short-outlet tee?

A tee whose branch is only as long as its flange needs: 41.3 mm (1.625 in) centre to face on 2 in, against 88.9 for the equal tee.