Library › 3D printable tri-clamp › Clamps & fittings ·

Snap tri-clamp, bolt-free (printable, ½ to 10 in)

Is there a tri-clamp clamp that snaps shut without a bolt? · Hardware · basis: Xem Studio design (v7, 6–10 in v8), tested on a 2 in printed joint

Also called: bolt free tri clamp, snap tri clamp, 3d printed tri clamp clamp, tool-less tri clamp, 6 inch snap tri clamp, 8 inch tri clamp printable, 10 inch tri clamp printable

Exact dimensions. True size, with no tolerance added.

sizes
9 in table

Notes

  • A tri-clamp clamp with no bolt: each piece carries a flush arm whose hooked claw drops into a notch on the next piece only when the two meet — clipped or not, nothing in between. Open with a butter knife in the V at the arm tip.
  • ½ to 8 in: two identical halves. 10 in: three identical 120° segments, because a 10 in half is wider than a 256 mm bed; each segment has one arm and one notch, the same latch.
  • Prints flat with no supports: every downward face is 45° or steeper, both outer edges carry the same R7 round. Every file fits a 256 × 256 mm bed as exported; the footprint column is one piece as it lies on the bed.
  • Sized for the printable 45° tri-clamp ferrules and a standard silicone gasket (closes on a 2.0 mm compressed stack). One clamp per flange: ½ and ¾ in share the 25 mm flange, 1 and 1½ in the 50.5 mm flange.
  • 6, 8 and 10 in carry more gasket force, so the wall, the band width and the arm thickness grow with the square root of the flange diameter (from the 4 in values); the claw, the groove and the knife V are the same as on the tested 2 in clamp, so one clamp key opens every size.
  • The STEP/STL pack (all sizes, ½ to 10 in) is $3 by card, or $2.40 for AI agents paying with x402 at /api/buy/snap-tri-clamp-pack. The dimension sheet is free.

Snap tri-clamp, bolt-free size chart

sizepiecesclamp ODwidthwallprint footprint (one piece)
½–¾ in (25 mm flange)2 halves43.0 mm16.0 mm8.0 mm42.3 × 26.4 mm
1–1½ in (50.5 mm flange)2 halves68.5 mm22.5 mm8.0 mm67.4 × 42.2 mm
2 in (64 mm flange)2 halves82.0 mm23.3 mm8.0 mm80.7 × 50.6 mm
2½ in (77.5 mm flange)2 halves95.5 mm24.1 mm8.0 mm94.0 × 59.0 mm
3 in (91 mm flange)2 halves109.0 mm24.9 mm8.0 mm107.3 × 67.4 mm
4 in (119 mm flange)2 halves137.0 mm27.5 mm8.0 mm134.9 × 84.8 mm
6 in (166.9 mm flange)2 halves187.8 mm32.6 mm9.5 mm185.7 × 113.3 mm
8 in (217.7 mm flange)2 halves241.3 mm37.2 mm10.8 mm239.1 × 142.9 mm
10 in (268.5 mm flange)3 segments (120°)294.5 mm41.3 mm12.0 mm218.5 × 172.1 mm

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

Xem StudioSnap tri-clamp designwebPublisher's page; dimensions are facts

Files

Files $3.00 zip: STEP + STL per size, 9 parts, 2407 KB.

Buy the files, $3.00 card checkout by Stripe; the download starts right after.

AI agents pay $2.40 with x402 (USDC on Base, no account): https://xemstudio.com/api/buy/snap-tri-clamp-pack answers 402 with the price; pay and retry. The dimension sheet above is free.

Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=snap-tri-clamp-bolt-free

Snap tri-clamp, bolt-free (printable, ½ to 10 in), isometric render of a generated part
Schematic, not to scale.

Fits with

Questions

How do you open it?

Slide a butter knife into the V at an arm tip and lever the tip outward. The V is the same on every size.

Does it need supports?

No — it prints flat; every downward face is 45° or steeper.

Will the big sizes fit my printer?

Yes on a 256 × 256 mm bed: a 6 in half is 186 × 113 mm, an 8 in half 239 × 143 mm, a 10 in segment 219 × 172 mm, each as exported.

Why is the 10 in clamp three pieces?

A 10 in half would be 292 mm wide and does not fit a 256 mm bed even turned diagonally; three 120° segments do, each with the same claw latch.

Does the 10 in clamp have printable rims to go with it?

It fits any 10 in rim with the 45° back cone; the 10 in rim itself (268.5 mm flange) needs a printer larger than 256 mm.