Library › Tri-clamp & pipe › Clamp fittings ·
Tri-clamp gasket, ISO 2852 Type B: 1.5 and 2 in
What are the dimensions of a 2 inch tri-clamp gasket? · Hardware · basis: ISO 2852 Type B (Figure 3): web T1 1.7, a bulge each side on the groove diameter (U 5.5 overall, R5 1.2, R4 0.4), inner lip T4 1.1 × T2 2.8; measured from the files
Also called: tri clamp gasket, sanitary gasket 2 inch, tri clamp gasket dimensions, type b gasket, empaque tri clamp, vedação tri clamp
Used in Long Earth Society builds. 3-foot Stirling engine · Finned tri-clamp heat sink with PTFE thermal break
Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features
- sizes
- 2 in table
Notes
- The Type B gasket between two ISO 2852 faces: a 1.7 mm web on the flat faces, a bulge on each side centred on the groove diameter that sits in each face's gasket groove (5.5 mm over both; each 1.9 proud of the web in a 1.6 deep groove, so 0.3 squeeze each side, designed), and an inner lip into the bore.
- 2 in: OD Ø63.0, bulges on Ø56.5, lip ID Ø45.3. 1.5 in: OD Ø49.5, bulges on Ø43.5, lip ID Ø32.6. The lip is 1.1 mm thick radially inside the bore and 2.8 mm long, centred on the joint plane: 0.55 mm past each face. The published gasket ID (2 in 47.7, 1.5 in 35.0) is the web's ID where the lip starts.
- The sanitary-clamp gasket page carries the same profile for every size ½ to 4 in.
Tri-clamp gasket, ISO 2852 Type B: 1.5 and 2 in size chart
| size (in) | od (mm) | bulge on dia (mm) | web id (mm) | lip id (mm) | overall (mm) | web (mm) | lip length (mm) |
|---|---|---|---|---|---|---|---|
| 1.5 | 49.5 | 43.5 | 35.0 | 32.6 | 5.5 | 1.7 | 2.8 |
| 2 | 63.0 | 56.5 | 47.7 | 45.3 | 5.5 | 1.7 | 2.8 |
Mating features
Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.
| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| gasket bulges | on the groove Ø per size (Ø43.5 / Ø56.5), 5.5 overall, R5 1.2 | the two faces' gasket grooves (1.6 deep): 0.3 squeeze each side | designed | tc-gasket-* |
| gasket lip | ID = bore − 2.2, 2.8 long | the bore, 0.55 past each face | designed | tc-gasket-* |
Where the files are
Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.
| L.J. Star | Sanitary clamp gaskets: a good seal compresses the gasket about 0.3 mm | web | maker page verify |
| Rubber Fab | Tri-Clamp gasket dimensional chart: gasket ID, OD and bead diameter per size (2 in bead 2.22 in / 56.50 mm, 1.5 in 1.71 / 43.50, 3 in 3.29 / 83.50) | maker chart; dimensions are facts verify | |
| ISO (via iTeh sample) | ISO 2852:1974 clamp liners with gaskets (face and gasket profile, §6.1 and §8) | standard excerpt; dimensions are facts | |
| McMaster-Carr | Sanitary caps and gaskets (free STEP per part, for your own design use; no redistribution) | STEP, PDF | McMaster-Carr site terms: personal design use, no redistribution verify |
Free files
★ Free files 2 parts. Generated by Xem Studio from the standard; threads are plain cylinders at major diameter. CC BY 4.0. index.json
Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.
Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp- Claude: Add to Claude
- ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
- Cursor: install with one click. VS Code: install with one click.
| tc-gasket-1.5in | 1.5 in gasket, ISO 2852 Type B: OD 49.5, 1.7 web, bulge on Ø43.5 each side (5.5 overall, tip R1.2, fillet R0.4), lip ID 32.6 × 2.8 long | STEP · STL |
| tc-gasket-2in | 2 in gasket, ISO 2852 Type B: OD 63.0, 1.7 web, bulge on Ø56.5 each side (5.5 overall, tip R1.2, fillet R0.4), lip ID 45.3 × 2.8 long | STEP · STL |
https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.Plain text: sheet.txt · JSON: /api/geometry?object=tri-clamp-gasket

How it fits
Goes in or on
Connects to
Alternatives
Questions
What are 1.5 and 2 inch tri-clamp gasket dimensions?
1.5 in: Ø49.5 OD, Ø32.6 lip ID. 2 in: Ø63.0 OD, Ø45.3 lip ID. Both: 1.7 mm web, 5.5 mm over the two bulges, lip 2.8 mm long.
Where does the gasket bead sit?
In the gasket groove of each face, centred on the groove diameter (Ø43.5 / Ø56.5): a 1.6 mm deep groove with a 1.2 bottom radius; the bulge stands 1.9 proud of the web, so it is squeezed 0.3 mm.