Library › Hardware › Gears, cranks & flywheels ·

Two-throw crank webs 90° apart on a Ø3 shaft

What two-throw crank fits a 3 mm shaft? · Hardware · basis: Design values: 6 mm throws (12 mm strokes), Ø3 pins and shaft, 623 con-rod eyes (R7)

Also called: two throw crank 90 degrees, built up crank stirling, inner crank tri clamp, crank inside crankcase stirling

Long Earth Society build part. The crank inside my cross gamma. Long Earth Society

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
2 in table

Notes

  • A built-up crank small enough to turn inside a Ø29 chamber in the middle of the cross. The hub web goes on the end of the Ø3 shaft (M3 grub); a Ø3 × 12 dowel pressed through its disc is the diaphragm crank pin; the con-rod for the diaphragm turns on it; the link web is pressed on the pin's far end.
  • The link web carries the displacer pin, a second Ø3 × 12 dowel, 90° on from the diaphragm pin. Each pin passes only through its own con-rod: the shaft stops in the hub web, the diaphragm pin stops in the link web, the displacer pin starts there, so no con-rod eye ever meets another pin.
  • Both throws are 6 mm. The con-rod eyes sweep a radius of 13; the webs are Ø20.

Two-throw crank webs 90° apart on a Ø3 shaft size chart

filehub (mm)disc (mm)pins
inner-crank-web-hub-r6Ø10 × 6, Ø3 bore, M3 grubØ20 × 41 at r 6
inner-crank-web-link-r6Ø20 × 5.52 at r 6, 90° apart

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
shaft boreØ3Ø3 crankshaft (M3 grub)slideinner-crank-web-hub-*
grub holeØ2.5 (M3 tapped)set-m3x3designedinner-crank-web-hub-*
crank-pin holesØ3 at r 6 (link web: two, 90° apart)dowel-3x12 crank pinspressall
throw6 (12 mm strokes), displacer pin 90° onconrod-30 eyes (623)designedall

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

Long Earth SocietyEngine buildsweb, videoLES site

Free files

★ Free files 2 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
inner-crank-web-hub-r6hub web: Ø10 × 6 hub with Ø3 shaft bore and M3 grub hole (Ø2.5), Ø20 × 4 disc with the Ø3 crank-pin hole at r 6STEP · STL
inner-crank-web-link-r6link web: Ø20 × 5.5 disc, Ø3 pin holes at r 6, 90° apartSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=two-throw-crank-webs-3mm

Two-throw crank webs 90° apart on a Ø3 shaft, isometric render of a generated part
Render of inner-crank-web-link-r6 from the free STEP; not to scale.

Fits with

Questions

Which way does it turn?

So that the displacer pin is a quarter turn ahead of the diaphragm pin: the build list states the direction.

How is the link web held?

Pressed on the diaphragm pin, which is pressed in the hub web; the displacer pin is pressed in the link web.