Library › 3D printable tri-clamp › Caps, lids & ports ·

Printable tri-clamp (45°): dip-tube caps: 1½ and 2 in, ⅜ in tube 6 to 24 in long

How do I pull liquid out of the bottom of a tri-clamp vessel from the top (3D printable)? · Hardware · basis: Xem Studio design: the standard solid cap with a ⅜ in (9.53 × 1.2 wall) dip tube below and a ⅜ in hose barb (14MPHR barb profile) above; printable 45° back cone

Also called: tri clamp dip tube printable, fermenter dip tube printable, tri clamp racking cane printable, 3d printed tri clamp, 3d printable tri clamp, tri clamp stl, printable tri clover

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
10 in table

Notes

  • 3D-printable tri-clamp: this is Xem Studio's print-friendly version of the standard sanitary fitting, drawn so it prints on an ordinary FDM or resin printer with no supports. Download the STL to print it, or the STEP to edit it. The files are true size (no printing allowance): add your own clearance in the slicer or CAD if your printer needs it.
  • Transfer or sample from the bottom through the lid: push gas in another port and the liquid rises up the tube. For a 6 × 18 in vessel pick the 16 in tube (clears a dished bottom); 18 in reaches the floor.
  • Left out because they are taller than a 256 mm printer: dip-tube-cap-1.5in-12in, dip-tube-cap-1.5in-16in, dip-tube-cap-1.5in-18in, dip-tube-cap-1.5in-24in, dip-tube-cap-2in-12in, dip-tube-cap-2in-16in, dip-tube-cap-2in-18in, dip-tube-cap-2in-24in (the standard page has them).
  • Printable tri-clamp: the ISO 2852 face and gasket groove are exactly standard, only the back cone behind each rim is 45° instead of 20°, so no rim overhangs more than 45° from vertical in any print orientation. Join these with the 45° clamps (printable-tri-clamp-clamps) and standard Type B gaskets; a 45° clamp fits only 45° rims, so keep a run all 45°. A 45° cone turns clamp force into face force at 1 : 1 (a 20° cone at 2.7 : 1), so tighten the clamp bolts harder or use M6.
  • Print orientation: straight parts face down; elbows, tees and crosses with one face down; horizontal bores bridge their top, so keep them small or add a light tree support inside.
  • Every clamp face is the ISO 2852 profile used across this site: 2.85 mm rim, flat face with the gasket groove (K 1.6 deep, R3 1.2 bottom, 23° walls, P2 0.8 edges) on C2, 20° back cone. Flange C3 / groove C2 / tube OD × wall, mm: ½–¾ in 25.0 / 20.4 (derived) / 12.7–19.05 × 1.65; 1–1½ in 50.5 / 43.5 / 25.4–38.1 × 1.65; 2 in 64.0 / 56.5 / 50.8 × 1.65; 2½ in 77.5 / 70.5 / 63.5 × 1.65; 3 in 91.0 / 83.5 / 76.2 × 1.65; 4 in 119.0 / 110.0 / 101.6 × 2.11; 6 in 166.9 (6.570 in) / 156.5 / 152.4 × 2.77; 8 in 217.7 (8.570 in) / 207.0 / 203.2 × 2.77; 10 in 268.5 / 261.0 / 254.0 × 3.40; 12 in 319.3 / 311.8 / 304.8 × 3.40.

Printable tri-clamp (45°): dip-tube caps: 1½ and 2 in, ⅜ in tube 6… size chart

clamptube (in)tube (mm)
1–1½6152.4
1–1½12304.8
1–1½16406.4
1–1½18457.2
1–1½24609.6
26152.4
212304.8
216406.4
218457.2
224609.6

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
clamp faceISO 2852: 1–1½ in flange 50.5, groove 43.5; 2 in flange 64.0, groove 56.5; rim 2.85; 45° back conestandard Type B gasket and the 45° clamps (printable-tri-clamp-clamps): a 45° clamp fits only 45° rims, so keep a run all 45°clampdip-tube-cap-*
dip tubeØ9.53 × 1.2 wall (⅜ in), 152.4 to 609.6 longvessel depth: 16 in tube clears a dished bottom of a 6 × 18 in vessel, 18 in reaches the floordesigneddip-tube-cap-*
hose barb⅜ in, 14MPHR barb profile⅜ in hose pushed over the barbpressdip-tube-cap-*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

GW KentTri-clamp fittings guide: tube OD, flange OD and ID per size to 12 in; solid cap thicknesswebpublisher's guide; dimensions cited
Dixon14MPHR brewery hose barb: A and barb OD B (hose ID + 0.040 in) per size, ½ to 6 inPDFpublisher's catalogue; dimensions cited
Rubber FabTri-Clamp gasket dimensional chart: gasket ID, OD and bead diameter per size (2 in bead 2.22 in / 56.50 mm, 1.5 in 1.71 / 43.50, 3 in 3.29 / 83.50)PDFmaker chart; dimensions are facts verify

Free files

★ Free files 2 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
dip-tube-cap-1.5in-6in-451–1½ in cap with a ⅜ in (Ø9.53) dip tube 6 in below the face and a ⅜ in hose barb outside — printable, 45° rimsSTEP · STL
dip-tube-cap-2in-6in-452 in cap with a ⅜ in (Ø9.53) dip tube 6 in below the face and a ⅜ in hose barb outside — printable, 45° rimsSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=printable-tri-clamp-dip-tube-caps

Printable tri-clamp (45°): dip-tube caps: 1½ and 2 in, ⅜ in tube 6 to 24 in long, isometric render of a generated part
Render of dip-tube-cap-2in-6in-45 from the free STEP; not to scale.

Fits with

Questions

Can I 3D print this?

Yes. It is the 3D-printable version: every overhang is 45° or steeper, so it prints without supports, and the sealing face is standard ISO 2852, so a normal gasket and clamp fit.

Which length for a 6 × 18 in vessel?

16 in clears the dished bottom; use 18 in only with the round bottom.