Library › Tri-clamp & pipe › Caps & heads ·
Tri-clamp end cap with two 623 bearing towers and a Ø3 rod bore, 1.5, 2 and 3 in
What tri-clamp cap holds a small crankshaft on bearings? · Hardware · basis: ISO 2852 cap face; Ø3 run bore for the displacer rod; two 623 bearing pockets (Ø10) on a Ø3 crank axis 30 mm above the face
Also called: tri clamp crank head, stirling cap with crankshaft, tri clamp end cap bearing towers, displacer rod seal tri clamp, 623 bearing tri clamp cap
Long Earth Society build part. The displacers and heads the LES tri-clamp engines are built from. Long Earth Society
Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features
- sizes
- 3 in table
Notes
- An ISO 2852 end cap that carries both the displacer rod and a small crankshaft, so the drive sits right on the cylinder.
- On centre: a Ø18 × 9 boss with a Ø3 bore straight through for the Ø3 displacer rod (run fit); the bore is the rod guide and the clearance seal.
- Two towers 10 × 14 × 28 mm stand on the back of the 6 mm cap, centred ±(C3/2 − 11) from the axis (±14.25 / ±21.0 / ±34.5 mm for 1.5 / 2 / 3 in), each with a Ø10 pocket for a 623 bearing; the Ø3 crankshaft axis is 30 mm above the face, 24 mm above the cap's back.
- The overall height is 34 mm; flange Ø50.5 / 64.0 / 91.0.
Tri-clamp end cap with two 623 bearing towers and a Ø3 rod bore… size chart
| size (in) | flange od (mm) | rod bore (mm) | tower centres (mm) | bearing | crank axis above face (mm) |
|---|---|---|---|---|---|
| 1.5 | 50.5 | 3 | 28.5 | 623 (Ø10) | 30 |
| 2 | 64.0 | 3 | 42.0 | 623 (Ø10) | 30 |
| 3 | 91.0 | 3 | 69.0 | 623 (Ø10) | 30 |
Mating features
Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.
| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| bearing pockets | Ø10 | 623 bearing | press | head-crank-* |
| head faces | ISO 2852 | ferrule face + Type B gasket | clamp | head-* |
| rod-gland bore | Ø3 × 13.4 (through cap and Ø18 boss) | Ø3 displacer rod | run | head-crank-* |
Where the files are
Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.
| Long Earth Society | Tri-clamp Stirling engine builds | web, video | LES site |
| James R. Senft | An Introduction to Low Temperature Differential Stirling Engines (displacer and gap design) | book | Moriya Press verify |
| Wikipedia | Stirling engine | web | CC BY-SA 4.0 (text) |
Free files
★ Free files 3 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json
Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.
Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp- Claude: Add to Claude
- ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
- Cursor: install with one click. VS Code: install with one click.
| head-crank-1.5in | 1.5 in ISO 2852 cap: clearance-seal rod gland (Ø3 bore straight through the cap and its Ø18 boss, 13.4 mm long, for the Ø3 rod; no O-ring) and two 623 bearing towers for a Ø3 crankshaft 24 mm above the cap | STEP · STL |
| head-crank-2in | 2 in ISO 2852 cap: clearance-seal rod gland (Ø3 bore straight through the cap and its Ø18 boss, 13.4 mm long, for the Ø3 rod; no O-ring) and two 623 bearing towers for a Ø3 crankshaft 24 mm above the cap | STEP · STL |
| head-crank-3in | 3 in ISO 2852 cap: clearance-seal rod gland (Ø3 bore straight through the cap and its Ø18 boss, 13.4 mm long, for the Ø3 rod; no O-ring) and two 623 bearing towers for a Ø3 crankshaft 24 mm above the cap | STEP · STL |
https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.Plain text: sheet.txt · JSON: /api/geometry?object=tri-clamp-cap-623-bearing-towers

How it fits
Goes in or on
Connects to
Also needed
You might also need
Questions
How do I seal the displacer rod through a tri-clamp cap?
With a clearance seal: the crank head has a Ø3 bore straight through its Ø18 × 9 boss, and the Ø3 rod runs in it with no O-ring.
How high is the crankshaft on the crank head?
The Ø3 crank axis is 30 mm above the sealing face (24 mm above the cap's back), in two 623 bearings.
How far apart are the crank-head towers?
28.5 mm centre to centre on 1.5 in, 42.0 on 2 in, 69.0 on 3 in.

