Library › Hardware › Gears, cranks & flywheels ·

Crankshafts Ø3, Ø5 and Ø8 with full-length D-flat

What D-flat shafts are drawn for small cranks? · Hardware · basis: Solid shafts at the 623 / 625 / 608 bore Ø; Ø5 and Ø8 with a 0.5 mm D-flat along the whole length

Also called: stirling engine crankshaft, 5mm d shaft full length, 8mm crankshaft, model engine crankshaft step, 3mm crankshaft

Long Earth Society build part. The shafts, rods and pins every engine here turns on. Long Earth Society

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
11 in table

Notes

  • Solid round shafts with 0.3 chamfers on both ends. Ø3 × 40, 44, 60 and 80 are plain round; Ø5 × 80, 100, 120, 150 and Ø8 × 80, 100, 120 have a D-flat 0.5 deep along the whole length (4.5 and 7.5 across the flat).
  • The flat is where the M3 grubs in crank discs, webs and flywheel hubs bear, so the hubs cannot turn on the shaft. It also gives the shaft a flat face to lie on.
  • Ø3: the crank head's 623 towers and the Ø3-bore crank discs. Ø5: the 625 crank stands, rhombic gears, crank discs and Ø5 flywheel hubs. Ø8: the tri-clamp crank frame's 608s, crank webs and Ø8 flywheel hubs.
  • Lengths on the engines here: 2 in gamma Ø5 × 100 between two 625 stands with the flywheel outside; tri-clamp crank frame Ø8 × 80; rhombic gear shafts Ø5 × 80, one × 120 to carry the flywheel; can engine Ø3 × 44 and LTD Ø3 × 40 (a crank disc at each end, bearings and flywheel between).

Crankshafts Ø3, Ø5 and Ø8 with full-length D-flat size chart

fileØlengthD-flatfits
crankshaft-3x40340—623; crank-disc-b3
crankshaft-3x44344—623; crank-disc-b3
crankshaft-3x60360—623; crank-disc-b3
crankshaft-3x80380—623; crank-disc-b3
crankshaft-5x80-dflat5800.5 full length (4.5)625; crank discs; Ø5 hubs
crankshaft-5x100-dflat51000.5 full length (4.5)625; crank discs; Ø5 hubs
crankshaft-5x120-dflat51200.5 full length (4.5)625; crank discs; Ø5 hubs
crankshaft-5x150-dflat51500.5 full length (4.5)625; crank discs; Ø5 hubs
crankshaft-8x80-dflat8800.5 full length (7.5)608; crank webs; Ø8 hubs
crankshaft-8x100-dflat81000.5 full length (7.5)608; crank webs; Ø8 hubs
crankshaft-8x120-dflat81200.5 full length (7.5)608; crank webs; Ø8 hubs

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
shafts, rods, pinsØ3 / Ø5 / Ø8the bores listed on each mating objectslideall
D-flat0.5 deepM3 grubs in hubsdesignedcrankshaft-*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

Long Earth SocietyEngine buildsweb, videoLES site

Free files

★ Free files 11 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
crankshaft-3x40Ø3 × 40 solid crankshaft for the crank head's 623 towers and the Ø3-bore crank discs; can engine skewer replacementSTEP · STL
crankshaft-3x44Ø3 × 44 solid crankshaft for the crank head's 623 towers and the Ø3-bore crank discs; can engine skewer replacementSTEP · STL
crankshaft-3x60Ø3 × 60 solid crankshaft for the crank head's 623 towers and the Ø3-bore crank discs; can engine skewer replacementSTEP · STL
crankshaft-3x80Ø3 × 80 solid crankshaft for the crank head's 623 towers and the Ø3-bore crank discs; can engine skewer replacementSTEP · STL
crankshaft-5x80-dflatØ5 × 80 crankshaft with a full-length 0.5 mm D-flat (4.5 across) for the grubs; 625 crank stands, rhombic gears, crank discs, nut flywheel b5.STEP · STL
crankshaft-5x100-dflatØ5 × 100 crankshaft with a full-length 0.5 mm D-flat (4.5 across) for the grubs; 625 crank stands, rhombic gears, crank discs, nut flywheel b5.STEP · STL
crankshaft-5x120-dflatØ5 × 120 crankshaft with a full-length 0.5 mm D-flat (4.5 across) for the grubs; 625 crank stands, rhombic gears, crank discs, nut flywheel b5.STEP · STL
crankshaft-5x150-dflatØ5 × 150 crankshaft with a full-length 0.5 mm D-flat (4.5 across) for the grubs; 625 crank stands, rhombic gears, crank discs, nut flywheel b5.STEP · STL
crankshaft-8x80-dflatØ8 × 80 crankshaft with a full-length 0.5 mm D-flat (7.5 across); tri-clamp crank frame 608s, crank webs, flywheels b8.STEP · STL
crankshaft-8x100-dflatØ8 × 100 crankshaft with a full-length 0.5 mm D-flat (7.5 across); tri-clamp crank frame 608s, crank webs, flywheels b8.STEP · STL
crankshaft-8x120-dflatØ8 × 120 crankshaft with a full-length 0.5 mm D-flat (7.5 across); tri-clamp crank frame 608s, crank webs, flywheels b8.STEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=d-flat-crankshafts-3-5-8

Crankshafts Ø3, Ø5 and Ø8 with full-length D-flat, isometric render of a generated part
Render of crankshaft-5x100-dflat from the free STEP; not to scale.

You might also need

Questions

What diameter crankshaft does a model Stirling engine need?

The bore of its bearings: Ø3 in 623s, Ø5 in 625s, Ø8 in 608s. The Ø5 and Ø8 files carry a 0.5 mm D-flat along their whole length.

Why a D-flat?

So the M3 grub in each crank disc, web and flywheel hub bears on a flat and the hub cannot slip round the shaft.

How is this different from the metric shafts page?

Those have a 20 mm motor-style flat 0.1 × d deep at one end; these have a 0.5 mm flat along the whole length so a hub can sit anywhere.