Library › Tri-clamp & pipe › Caps & heads ·
Tri-clamp end cap with 608 bearing towers for a Ø8 shaft, 1.5, 2 and 3 in
What tri-clamp cap carries an 8 mm shaft on 608 bearings? · Hardware · basis: ISO 2852 cap face; pedestal Ø = tube OD to clear the clamp; two 8 mm towers with Ø22 608 pockets, 21 mm apart, crank axis 32 / 34 / 40 mm above the face
Also called: tri clamp stirling crankshaft frame, crank frame tri clamp, 608 crank mount stirling, tri clamp cap with bearing towers
Long Earth Society build part. Full-bore pistons for the tri-clamp beta and alpha engines. Long Earth Society
Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features
- sizes
- 3 in table
Notes
- A crank frame that clamps onto the open ferrule of a spool with a stock clamp and gasket, and holds a Ø8 crankshaft in two 608 bearings above it.
- Base: the 6 mm ISO 2852 cap, a pedestal the tube's OD (38.1 / 50.8 / 76.2) up to 14 mm so the clamp clears, and a Ø C3 plate 4 mm thick on top. A con-rod window Ø21 / Ø28 / Ø44 runs through the centre.
- Two towers 8 mm thick with rounded tops stand 21 mm apart; each has a Ø22 × 7 pocket for a 608 from the outside face, and the shaft hole between is Ø9.2 so the Ø8 shaft touches only the bearings.
- Crank axis 32 / 34 / 40 mm above the face for 1.5 / 2 / 3 in; overall height 47.7 / 54 / 60 mm.
Tri-clamp end cap with 608 bearing towers for a Ø8 shaft, 1.5, 2 and… size chart
| spool (in) | flange od (mm) | window (mm) | crank axis (mm) | tower gap (mm) | bearing | overall h (mm) |
|---|---|---|---|---|---|---|
| 1.5 | 50.5 | 21 | 32 | 21 | 608 (Ø22) | 47.7 |
| 2 | 64.0 | 28 | 34 | 21 | 608 (Ø22) | 54.0 |
| 3 | 91.0 | 44 | 40 | 21 | 608 (Ø22) | 60.0 |
Mating features
Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.
| feature | exact | mates with | fit | files |
|---|---|---|---|---|
| crank-frame bearing pockets | Ø22 | 608 bearing | press | crank-frame-* |
| crank-frame face | ISO 2852 | tri-clamp ferrule face + Type B gasket | clamp | crank-frame-* |
| crank-frame shaft clearance | Ø9.2 | Ø8 shaft (no contact; the 608s carry it) | designed | crank-frame-* |
Where the files are
Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.
| Long Earth Society | Tri-clamp Stirling engine builds | web, video | LES site |
| James R. Senft | An Introduction to Stirling Engines (piston fit and leakage) | book | Moriya Press verify |
| ASME | BPE tube dimensions (16 ga sanitary tube) | standard | ASME verify |
Free files
★ Free files 3 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json
Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.
Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp- Claude: Add to Claude
- ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
- Cursor: install with one click. VS Code: install with one click.
| crank-frame-1.5in | 1.5 in crank frame: ISO 2852 cap face (clamps to the spool with a stock clamp), Ø21 con-rod window, two towers with 608 pockets for a Ø8 crankshaft 32 mm above the face, 21 mm between towers | STEP · STL |
| crank-frame-2in | 2 in crank frame: ISO 2852 cap face (clamps to the spool with a stock clamp), Ø28 con-rod window, two towers with 608 pockets for a Ø8 crankshaft 34 mm above the face, 21 mm between towers | STEP · STL |
| crank-frame-3in | 3 in crank frame: ISO 2852 cap face (clamps to the spool with a stock clamp), Ø44 con-rod window, two towers with 608 pockets for a Ø8 crankshaft 40 mm above the face, 21 mm between towers | STEP · STL |
https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.Plain text: sheet.txt · JSON: /api/geometry?object=tri-clamp-cap-608-bearing-towers

How it fits
Goes in or on
Connects to
Also needed
You might also need
Questions
How do I put a crankshaft on a tri-clamp cylinder?
Clamp the crank frame to the open ferrule; a Ø8 shaft runs in two 608s in its towers, 34 mm above the face on the 2 in frame.
How wide is the gap between the crank-frame towers?
21 mm: crank web, con-rod, crank web (5 mm each) with 1 mm gaps.
Does the shaft touch the frame?
No: the shaft hole is Ø9.2; the Ø8 shaft runs only in the 608s.

