Library › Tri-clamp & pipe › Caps & heads ·

Tri-clamp end cap with a Ø3 rod bore and 4 mm hose barb, 1.5, 2 and 3 in

What tri-clamp end cap has a rod bore and a hose barb? · Hardware · basis: ISO 2852 cap face (Ø50.5 / 64.0 / 91.0 flange, 6 mm cap) with a Ø3 run bore on centre and a 4 mm hose barb

Also called: tri clamp end cap with rod guide, stirling displacer head, tri clamp cap 3mm rod, gamma stirling cold head, tri clamp cap with hose barb

Long Earth Society build part. The displacers and heads the LES tri-clamp engines are built from. Long Earth Society

Exact dimensions. Every file is drawn at true size with no tolerance added. The holes and pins that meet another part are listed below under Mating features, with the fit each joint needs; open those by your process's clearance before making the part. Mating features

sizes
3 in table

Notes

  • An ISO 2852 end cap with the displacer-rod guide and a transfer port on its back, so a stock clamp and Type B gasket seal it to any ferrule of its size.
  • On centre: a Ø3 bore straight through cap and boss for the Ø3 displacer rod (run fit). The bore is the rod guide and the clearance seal; nothing is pressed into it.
  • Off centre: an integral 4 mm hose barb (Ø6.4 base, Ø3.2 bore) for the transfer tube to the power cylinder, at 13.75 / 20.25 / 33.75 mm from the axis on the 1.5 / 2 / 3 in head.
  • Flange Ø50.5 (1.5 in, also fits 1 in ferrules), Ø64.0 (2 in), Ø91.0 (3 in).

Tri-clamp end cap with a Ø3 rod bore and 4 mm hose barb, 1.5, 2 and… size chart

size (in)flange od (mm)rod bore (mm)barbbarb offset (mm)
1.550.534 mm (Ø6.4, Ø3.2 bore)13.75
264.034 mm (Ø6.4, Ø3.2 bore)20.25
391.034 mm (Ø6.4, Ø3.2 bore)33.75

Mating features

Drawn at the exact size. Open press, slide, run and socket features by your process's clearance (tolerances by process); leave designed gaps and clamp fits as drawn.

featureexactmates withfitfiles
head facesISO 2852ferrule face + Type B gasketclamphead-*
transfer-port barbØ6.4 barb, Ø3.2 bore4 mm ID tubedesignedhead-displacer-*
rod-guide boreØ3 × 16.4 (through cap and Ø10 boss)Ø3 displacer rodrunhead-displacer-*

Where the files are

Other publishers' files are linked, not hosted. "verify" = check the license at the link before commercial use.

Long Earth SocietyTri-clamp Stirling engine buildsweb, videoLES site
James R. SenftAn Introduction to Low Temperature Differential Stirling Engines (displacer and gap design)bookMoriya Press verify
WikipediaStirling enginewebCC BY-SA 4.0 (text)

Free files

★ Free files 3 parts. Xem Studio design: free to use, print and sell things from; not to be republished as files. Xem Studio Design License. index.json

Use this part in your AI. Your AI gets the exact sizes and files straight from Xem and can design a mount, case or adapter around it. Direct downloads here are limited to one file every 10 minutes; through your AI they are unlimited.

Connect Xem to your AI (free, no account, about a minute)
https://xemstudio.com/mcp
  1. Claude: Add to Claude
  2. ChatGPT (Plus or higher): open Connectors → Advanced → turn on Developer mode → Create → paste the address, no authentication → Create.
  3. Cursor: install with one click. VS Code: install with one click.
Other apps and full steps
head-displacer-1.5in1.5 in ISO 2852 cap: Ø3 rod-guide bore straight through the cap and its Ø10 × 12 boss for the Ø3 displacer rod (running fit, see Mating features); 4 mm transfer-port barbSTEP · STL
head-displacer-2in2 in ISO 2852 cap: Ø3 rod-guide bore straight through the cap and its Ø10 × 12 boss for the Ø3 displacer rod (running fit, see Mating features); 4 mm transfer-port barbSTEP · STL
head-displacer-3in3 in ISO 2852 cap: Ø3 rod-guide bore straight through the cap and its Ø10 × 12 boss for the Ø3 displacer rod (running fit, see Mating features); 4 mm transfer-port barbSTEP · STL
Let your AI pull this. Add https://xemstudio.com/mcp to Claude, ChatGPT, Cursor or any MCP client (free, no account, one minute) and it can look up exact sizes, mating fits and free STEP/STL from every chat.
Set it up →

Plain text: sheet.txt · JSON: /api/geometry?object=tri-clamp-cap-rod-bore-hose-barb

Tri-clamp end cap with a Ø3 rod bore and 4 mm hose barb, 1.5, 2 and 3 in, isometric render of a generated part
Render of head-displacer-2in from the free STEP; not to scale.

You might also need

Questions

How does the displacer rod get out of a tri-clamp cylinder?

Through the Ø3 bore on the centre of this head: the Ø3 rod runs in it, and the bore length is the clearance seal.

What is the barb on the displacer head for?

The transfer port: a 4 mm barb (Ø6.4 base, Ø3.2 bore) for the tube to the power cylinder.

Does it need a special clamp?

No: the face is ISO 2852, so a stock clamp and Type B gasket for the flange size seal it.